Watch
1
0
Fork
You've already forked kernel_a52xq
0
mirror of https://github.com/a52xq-dev/kernel.git synced 2026-11-22 01:46:57 +07:00
Commit graph kernel_a52xq/drivers/mtd/nand/raw
Message SHA1
treewide: Use array_size() in vmalloc()
The vmalloc() function has no 2-factor argument form, so multiplication
factors need to be wrapped in array_size(). This patch replaces cases of:

        vmalloc(a * b)

with:
        vmalloc(array_size(a, b))

as well as handling cases of:

        vmalloc(a * b * c)

with:

        vmalloc(array3_size(a, b, c))

This does, however, attempt to ignore constant size factors like:

        vmalloc(4 * 1024)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  vmalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  vmalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  vmalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  vmalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
  vmalloc(
-	sizeof(TYPE) * (COUNT_ID)
+	array_size(COUNT_ID, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(TYPE) * COUNT_ID
+	array_size(COUNT_ID, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(TYPE) * (COUNT_CONST)
+	array_size(COUNT_CONST, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(TYPE) * COUNT_CONST
+	array_size(COUNT_CONST, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(THING) * (COUNT_ID)
+	array_size(COUNT_ID, sizeof(THING))
  , ...)
|
  vmalloc(
-	sizeof(THING) * COUNT_ID
+	array_size(COUNT_ID, sizeof(THING))
  , ...)
|
  vmalloc(
-	sizeof(THING) * (COUNT_CONST)
+	array_size(COUNT_CONST, sizeof(THING))
  , ...)
|
  vmalloc(
-	sizeof(THING) * COUNT_CONST
+	array_size(COUNT_CONST, sizeof(THING))
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

  vmalloc(
-	SIZE * COUNT
+	array_size(COUNT, SIZE)
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  vmalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  vmalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  vmalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  vmalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  vmalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  vmalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  vmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  vmalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  vmalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  vmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  vmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  vmalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  vmalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  vmalloc(C1 * C2 * C3, ...)
|
  vmalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants.
@@
expression E1, E2;
constant C1, C2;
@@

(
  vmalloc(C1 * C2, ...)
|
  vmalloc(
-	E1 * E2
+	array_size(E1, E2)
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>

Kees Cook   commited 2018-06-12 16:19:22 -07:00
42bc47b353
treewide: devm_kzalloc() -> devm_kcalloc()
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:

        devm_kzalloc(handle, a * b, gfp)

with:
        devm_kcalloc(handle, a * b, gfp)

as well as handling cases of:

        devm_kzalloc(handle, a * b * c, gfp)

with:

        devm_kzalloc(handle, array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        devm_kcalloc(handle, array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        devm_kzalloc(handle, 4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@

(
  devm_kzalloc(HANDLE,
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  devm_kzalloc(HANDLE,
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@

- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@

(
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
  devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * E2
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>

Kees Cook   commited 2018-06-12 16:19:22 -07:00
a86854d0c5
treewide: kmalloc() -> kmalloc_array()
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:

        kmalloc(a * b, gfp)

with:
        kmalloc_array(a * b, gfp)

as well as handling cases of:

        kmalloc(a * b * c, gfp)

with:

        kmalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kmalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kmalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kmalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kmalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kmalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kmalloc
+ kmalloc_array
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kmalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kmalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kmalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kmalloc(sizeof(THING) * C2, ...)
|
  kmalloc(sizeof(TYPE) * C2, ...)
|
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>

Kees Cook   commited 2018-06-12 16:19:22 -07:00
6da2ec5605
MTD changes:
Core changes:
   - Add a sysfs attribute to expose available OOB size
 
   Driver changes:
   - Remove HAS_DMA dependency on various drivers
   - Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
   - Replace msleep by usleep_range() in the dataflash driver
   - Avoid VLA usage in nftl layers
   - Remove useless .owner assignment in pismo
   - Fix various issues in the CFI driver
   - Improve TRX partition handling expose a DT compat for this part
     parser
   - Clarify OFFSET_CONTINUOUS meaning
 
 NAND changes:
   Core changes:
   - Add Miquel as a NAND maintainer
   - Add access mode to the nand_page_io_req struct
   - Fix kernel-doc in rawnand.h
   - Support bit-wise majority to recover from corrupted ONFI parameter
     pages
   - Stop checking FAIL bit after a SET_FEATURES, as documented in the
     ONFI spec
 
   Raw NAND Driver changes:
   - Fix and cleanup the error path of many NAND controller drivers
   - GPMI:
     * Cleanup/simplification of a few aspects in the driver
     * Take ECC setup specified in the DT into account
   - sunxi: remove support for GPIO-based R/B polling
   - MTK:
     * Use of_device_get_match_data() instead of of_match_device()
     * Add an entry in MAINTAINERS for this driver
     * Fix nand-ecc-step-size and nand-ecc-strength description in the DT
       bindings doc
   - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
 
   OneNAND driver changes:
   - samsung: use dev_get_drvdata() instead of platform_get_drvdata()
 
 SPI NOR changes:
   Core changes:
   - Add support for a bunch of SPI NOR chips
   - Clear EAR reg when switching to 3-byte addressing mode on Winbond
     chips
 
   SPI NOR controller driver changes:
   - cadence: Add DMA support for direct mode reads
   - hisi: Prefix a few functions with hisi_
   - intel:
     * Mark the driver as "dangerous" in Kconfig
     * Fix atomic sequence handling
     * Pass a 40us delay (instead of 0us) to readl_poll_timeout()
   - fsl:
     * fix a typo in a function name
     * add support for IP variants embedded in the ls2080a and ls1080a
       SoCs
   - stm32: request exclusive control of the reset line
 -----BEGIN PGP SIGNATURE-----
 
 iQI5BAABCAAjBQJbGZ/KHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
 Ze02AX4ItwBhLRAAqj0wXUjyO836NSqYboF21b+eLCLAOojydRCIQjbMYkEQ1ifZ
 vLEwHy8vDYYnJyT+cXlP8wpImh7grhCrq3jPW/SDU2xljUC4TXAAVrfSYw6EJ5at
 TJBum4+DVkTr3ZgBUI/RxDmao0i+29ztK/viHnLEeDziWaFGJqy0C8FtMwFf6MTF
 LwbmCD0KppoLUP0CW/V+fITu8+FBOFsLdDXUi//GIIMeUE3smvGbhXrRZsFoXC3p
 5sgo6Dn3f87uO/fK2x2YNf9uXAb2fRuqnCmXwu+AXEW1NLBzkU0TlxerPxbbrmAR
 wNqBRK/mw+uIILAZgi8tiCRreFYGNNefK+cpf7lqFpZVgBWJJxBMkfy1UdXupUQx
 N/2J+UpGKlGtevvW1CnTXvK0zeXg8FwGREXL4il02Sg57s7IkvG/xIoSN2Nofs9K
 KULDJ8CE1BtH/LwdKHpe7DLzc1I3E8DRzzbVzEzZuW/ukMnqCgouF4wNsjmUJHmm
 KfCNan8CWCU6QyqVIGd3ucm5RXwwaEiMrXxoCmjmkJy8+4eDTYNWgruFSU/adOtU
 lABuvzVzoJ3UKvdxjlirg83EcWrazj4W2/COz+Hpxaa+vAwAPb1GoxyNKqGpdL8p
 lugJOps4rHuFF6xJX/AwSrL5C1cmpuKXICqkErTieKT1YZhpx72v7rFXEK4=
 =cHjU
 -----END PGP SIGNATURE-----

Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd

Pull MTD updates from Boris Brezillon:
 "Core changes:
   - Add a sysfs attribute to expose available OOB size

  Driver changes:
   - Remove HAS_DMA dependency on various drivers
   - Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
   - Replace msleep by usleep_range() in the dataflash driver
   - Avoid VLA usage in nftl layers
   - Remove useless .owner assignment in pismo
   - Fix various issues in the CFI driver
   - Improve TRX partition handling expose a DT compat for this part
     parser
   - Clarify OFFSET_CONTINUOUS meaning

  NAND core changes:
   - Add Miquel as a NAND maintainer
   - Add access mode to the nand_page_io_req struct
   - Fix kernel-doc in rawnand.h
   - Support bit-wise majority to recover from corrupted ONFI parameter
     pages
   - Stop checking FAIL bit after a SET_FEATURES, as documented in the
     ONFI spec

  Raw NAND Driver changes:
   - Fix and cleanup the error path of many NAND controller drivers
   - GPMI:
      + Cleanup/simplification of a few aspects in the driver
      + Take ECC setup specified in the DT into account
   - sunxi: remove support for GPIO-based R/B polling
   - MTK:
      + Use of_device_get_match_data() instead of of_match_device()
      + Add an entry in MAINTAINERS for this driver
      + Fix nand-ecc-step-size and nand-ecc-strength description in the
        DT bindings doc
   - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page

  OneNAND driver changes:
   - samsung: use dev_get_drvdata() instead of platform_get_drvdata()

  SPI NOR core changes:
   - Add support for a bunch of SPI NOR chips
   - Clear EAR reg when switching to 3-byte addressing mode on Winbond
     chips

  SPI NOR controller driver changes:
   - cadence: Add DMA support for direct mode reads
   - hisi: Prefix a few functions with hisi_
   - intel:
      + Mark the driver as "dangerous" in Kconfig
      + Fix atomic sequence handling
      + Pass a 40us delay (instead of 0us) to readl_poll_timeout()
   - fsl:
      + fix a typo in a function name
      + add support for IP variants embedded in the ls2080a and ls1080a
        SoCs
   - stm32: request exclusive control of the reset line"

* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
  mtd: nand: Pass mode information to nand_page_io_req
  mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
  mtd: cfi_cmdset_0002: Change erase functions to check chip good only
  mtd: cfi_cmdset_0002: Change erase functions to retry for error
  mtd: cfi_cmdset_0002: Change definition naming to retry write operation
  mtd: cfi_cmdset_0002: Change write buffer to check correct value
  mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
  mtd: bcm47xxpart: add of_match_table with a new DT binding
  dt-bindings: mtd: document Broadcom's BCM47xx partitions
  mtd: spi-nor: Add support for EN25QH32
  mtd: spi-nor: Add support for is25wp series chips
  mtd: spi-nor: Add Winbond w25q32jv support
  mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
  mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
  mtd: spi-nor: intel: provide a range for poll_timout
  mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
  mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
  mtd: spi-nor: intel-spi: Fix atomic sequence handling
  mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
  mtd: rawnand: use bit-wise majority to recover the ONFI param page
  ...

Linus Torvalds   commited 2018-06-08 10:39:20 -07:00
f4e70c2e5f
Core changes:
- Add Miquel as a NAND maintainer
 - Add access mode to the nand_page_io_req struct
 - Fix kernel-doc in rawnand.h
 - Support bit-wise majority to recover from corrupted ONFI parameter
   pages
 - Stop checking FAIL bit after a SET_FEATURES, as documented in the
   ONFI spec
 
 Raw NAND Driver changes:
 - Fix and cleanup the error path of many NAND controller drivers
 - GPMI:
   * Cleanup/simplification of a few aspects in the driver
   * Take ECC setup specified in the DT into account
 - sunxi: remove support for GPIO-based R/B polling
 - MTK:
   * Use of_device_get_match_data() instead of of_match_device()
   * Add an entry in MAINTAINERS for this driver
   * Fix nand-ecc-step-size and nand-ecc-strength description in the DT
     bindings doc
 - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
 
 OneNAND driver changes:
 - samsung: use dev_get_drvdata() instead of platform_get_drvdata()
 -----BEGIN PGP SIGNATURE-----
 
 iQI5BAABCAAjBQJbFP6lHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
 Ze02AX4ItwBVzRAAotaLsXzKMQXwDSTkRdTNFtpCuzgmmqO22PyKWai7lYAN29D4
 1g4V9UGkKxp5Wiy5iWADze41uxoOOZjlhxghnUNtqTLeB6FtAByBSai7hqV6jVwR
 QhSaf24a/bWcpmvMkYUM+odztwcFR1T1uq21JxDzMnt35RFG/Td4Fh7hz1eLxksB
 x7t3uiDDz5MoPo6/EGuw4MychXoYUnWxm6JNUQsQdZvAEBo1Rqd/8OIy+BHMH6BY
 GlNKJJtdhXoSmX1G48HzwB2FZdxwcaJT36Zcu1DgzWSN/Ivx6oKQDFPDzCAcg3S8
 7yUUNX1X2HavhVMiINi0lgLpI7kwiwl2bYZtHO5xUycHh9EKdgBiesQ1OkXg8w4Q
 zTJQH2krpS44VDa/iJhrc/zGnBPWn8jPScswZ89doymwkZA1pBfFjKoPvJVybvtv
 h84FAMHORpfyf9FHZhs72RFihy/pHPTtQlQpDl4o8e+vjne1+nCfCgBpXucjtUMK
 z99R/6//38StdWlGJCTapZ9Veg0lMiMWPNLWuOrIkzMY3GuEQjq2qjF1BCLs0Di9
 fUPo5VLtijL0vuR4YXg2XkXQ8qrqUrZjgxHUlhBsj31s3EGBDkPErkoDTdtN2rJF
 38jwPwSqIoMfOlRRkqq5FGopXrWMS5NEZkEdmVoymYZdauwCTuozGP8Xz7k=
 =MzWF
 -----END PGP SIGNATURE-----

Merge tag 'nand/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next

Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
  pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
  ONFI spec

Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
  * Cleanup/simplification of a few aspects in the driver
  * Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
  * Use of_device_get_match_data() instead of of_match_device()
  * Add an entry in MAINTAINERS for this driver
  * Fix nand-ecc-step-size and nand-ecc-strength description in the DT
    bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page

OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()

Boris Brezillon   commited 2018-06-07 22:52:56 +02:00
6e89b84e28
Refactors rslib and callers to provide a per-instance allocation area
instead of performing VLAs on the stack.
 -----BEGIN PGP SIGNATURE-----
 Comment: Kees Cook <kees@outflux.net>
 
 iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAlsUv+MWHGtlZXNjb29r
 QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJsL4D/0arl2+HZtG3GV6zMHbH1T3J0a3
 mZojEEZqgByx0vlN/Ai57YK4ADHKlF3oYqpXamc718iAmDfKgvbdG+IPv6hg0MQR
 c6F+ogSbcZ38vY7t08Iaa9cBQcKFJwJGAbYXyKV6dKp0ddPqNBBxHG0CLSWL+3DE
 ZxKRKQFQKZWJR587CjA9geZOImgYJG8Jq9Ue4fp1fKacBEBiZTtI/Y8C4XlrxZz6
 6p7BdarMXKqxW8B8vpE4xfCCkm8QGAfEuAXzMrqFLZhj48bg7+Tqd3d4AHm28hMp
 Q2eHyS9j4wWN+OxA1R+VIuzciz/vfWZJi1N7zSV8LznPPLICX8Vl4gXw+MkrELYV
 vzZRlRH67E993bsj0Xp65w7Zwc3MJKVfJOUq+3qR3I1JytCSOBsLs2w/VE2bzpeO
 jFD4gUJxYnl5s2UnCiHVgUzbgXE/n+JQS3Acf71qfAsb+Ld2/q9Tyjx7p7sm5IfB
 m/lokrSgBajtHPZfB6pQV2AvaoLIbWW9Lf1p84zA6XAwdAnAESffUGQHEK/W02a7
 ftwxXnOvjgRZJ/lUfOb0GQDgQniXO7cN7AcmKAfL+DNZb0j86esR6PuZDCIeDhTJ
 KcTVcwPtFnI4W+H3vagh+mLHf7bL/RgLngjUZd6PHqS+cVQfKFiNe43zlRl9+eRj
 U20+w5VfwSkrmAgfSw==
 =Z1if
 -----END PGP SIGNATURE-----

Merge tag 'rslib-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux

Pull reed-salomon library updates from Kees Cook:
 "Refactors rslib and callers to provide a per-instance allocation area
  instead of performing VLAs on the stack"

* tag 'rslib-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  rslib: Allocate decoder buffers to avoid VLAs
  mtd: rawnand: diskonchip: Allocate rs control per instance
  rslib: Split rs control struct
  rslib: Simplify error path
  rslib: Remove GPL boilerplate
  rslib: Add SPDX identifiers
  rslib: Cleanup top level comments
  rslib: Cleanup whitespace damage
  dm/verity_fec: Use GFP aware reed solomon init
  rslib: Add GFP aware init function

Linus Torvalds   commited 2018-06-05 10:48:05 -07:00
25d80be86c
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
The ONFI spec clearly says that FAIL bit is only valid for PROGRAM,
ERASE and READ-with-on-die-ECC operations, and should be ignored
otherwise.

It seems that checking it after sending a SET_FEATURES is a bad idea
because a previous READ, PROGRAM or ERASE op may have failed, and
depending on the implementation, the FAIL bit is not cleared until a
new READ, PROGRAM or ERASE is started.

This leads to ->set_features() returning -EIO while it actually worked,
which can sometimes stop a batch of READ/PROGRAM ops.

Note that we only fix the ->exec_op() path here, because some drivers
are abusing the NAND_STATUS_FAIL flag in their ->waitfunc()
implementation to propagate other kind of errors, like
wait-ready-timeout or controller-related errors. Let's not try to fix
those drivers since they worked fine so far.

Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>

Boris Brezillon   commited 2018-05-15 22:58:07 +02:00
782d1967d0
mtd: rawnand: marvell: Fix read logic for layouts with ->nchunks > 2
The code is doing monolithic reads for all chunks except the last one
which is wrong since a monolithic read will issue the
READ0+ADDRS+READ_START sequence. It not only takes longer because it
forces the NAND chip to reload the page content into its internal
cache, but by doing that we also reset the column pointer to 0, which
means we'll always read the first chunk instead of moving to the next
one.

Rework the code to do a monolithic read only for the first chunk,
then switch to naked reads for all intermediate chunks and finally
issue a last naked read for the last chunk.

Fixes: 02f26ecf8c mtd: nand: add reworked Marvell NAND controller driver
Cc: stable@vger.kernel.org
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>

Boris Brezillon   commited 2018-05-14 14:46:20 +02:00
90d6176333
mtd: rawnand: use bit-wise majority to recover the ONFI param page
Per ONFI specification (Rev. 4.0), if all parameter pages have invalid
CRC values, the bit-wise majority may be used to recover the contents
of the parameter page from the parameter page copies present.

Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Wan, Jane (Nokia - US/Sunnyvale)   authored and   Boris Brezillon   commited 2018-05-13 09:50:16 +02:00
39138c1f4a
mtd: rawnand: Make sure we wait tWB before polling the STATUS reg
NAND chips require a bit of time to take the NAND operation into
account and set the BUSY bit in the STATUS reg. Make sure we don't poll
the STATUS reg too early in nand_soft_waitrdy().

Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>

Boris Brezillon   commited 2018-05-10 08:40:39 +02:00
3057fcef38
mtd: rawnand: fsl_ifc: fix FSL NAND driver to read all ONFI parameter pages
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.

Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Jane Wan   authored and   Boris Brezillon   commited 2018-05-09 16:04:21 +02:00
a75bbe71a2
mtd: rawnand: marvell: fix command xtype in BCH write hook
One layout supported by the Marvell NAND controller supports NAND pages
of 2048 bytes, all handled in one single chunk when using BCH with a
strength of 4-bit per 512 bytes. In this case, instead of the generic
XTYPE_WRITE_DISPATCH/XTYPE_LAST_NAKED_RW couple, the controller expects
to receive XTYPE_MONOLITHIC_RW.

This fixes problems at boot like:

[    1.315475] Scanning device for bad blocks
[    3.203108] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[    3.209564] nand_bbt: error while writing BBT block -110
[    4.243106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[    5.283106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[    5.289562] nand_bbt: error -110 while marking block 2047 bad
[    6.323106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[    6.329559] nand_bbt: error while writing BBT block -110
[    7.363106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[    8.403105] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[    8.409559] nand_bbt: error -110 while marking block 2046 bad
...

Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-05-04 10:35:04 +02:00
a2ee41fd95
mtd: rawnand: marvell: pass ms delay to wait_op
marvell_nfc_wait_op() expects the delay to be expressed in milliseconds
but nand_sdr_timings uses picoseconds. Use PSEC_TO_MSEC when passing
tPROG_max to marvell_nfc_wait_op().

Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Chris Packham   authored and   Boris Brezillon   commited 2018-05-04 10:33:28 +02:00
b76401fc4b
mtd: rawnand: gpmi: remove unnecessary variables
Use this->auxiliary_virt and this->auxiliary_phys directly rather
than creating extra local variables for them.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sascha Hauer   authored and   Boris Brezillon   commited 2018-04-29 08:56:48 +02:00
f6b74db84c
mtd: rawnand: gpmi: return valid value from bch_set_geometry()
The caller of bch_set_geometry() expects the return value to
be an error code, so !0 is not valid. return the error from the
just called function instead.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sascha Hauer   authored and   Boris Brezillon   commited 2018-04-29 08:56:48 +02:00
e637f5fe8e
mtd: rawnand: gpmi: remove direct_dma_map_ok from driver data struct
Instead of putting direct_dma_map_ok into driver struct pass it around
between functions to make the code more readable.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sascha Hauer   authored and   Boris Brezillon   commited 2018-04-29 08:56:48 +02:00
111bfed4f3
mtd: rawnand: gpmi: put only once used functions inline
read_page_prepare(), read_page_end() and read_page_swap_end() are
trivial functions that are used only once and take 8 arguments each.
De-obfuscate the code by open coding these functions in
gpmi_ecc_read_page()

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sascha Hauer   authored and   Boris Brezillon   commited 2018-04-29 08:56:47 +02:00
118c3f9b01
mtd: rawnand: gpmi: pass buffer and len around
Instead of putting the buffer and len passed in from the mtd core
into the private data struct, just pass it around in the GPMI
drivers functions. This makes the lifetime of the variables more
clear and the code easier to follow.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sascha Hauer   authored and   Boris Brezillon   commited 2018-04-29 08:56:47 +02:00
ba3900e6fa
mtd: rawnand: gpmi: drop dma_ops_type
The GPMI nand driver puts dma_ops_type in its private data struct. Based
on the ops type the DMA callback handler unmaps previously mapped
buffers. Instead of unmapping the buffers in the DMA callback handler,
do this in the caller directly which waits for the DMA transfer to
finish. This makes the whole dma_ops_type mechanism unnecessary.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sascha Hauer   authored and   Boris Brezillon   commited 2018-04-29 08:56:46 +02:00
c3ee3f3db1
mtd: rawnand: add a way to pass an ID table with nand_scan()
As part of the work of migrating all the drivers to nand_scan(), and
because nand_scan() does not provide a way to pass an ID table, rename
the function nand_scan_with_ids() and add a third parameter to give a
flash ID table (like what was done with nand_scan_ident()).

Create a nand_scan() helper that is just a wrapper of
nand_scan_with_ids(), passing NULL as the ID table. This way a
controller drivers can continue using nand_scan() transparently.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:46 +02:00
256c4fc76a
mtd: rawnand: lpc32xx_slc: fix the probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup() and not
a nand_release(). The latter doing an mtd_device_unregister() which is
not needed if mtd_device_register() failed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:46 +02:00
553b0c6416
mtd: rawnand: lpc32xx_slc: clean the probe function
Before fixing the error path of the probe function, fix the style of the
entire function and particularly the goto labels: they should indicate
what the next cleanup to do is.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:45 +02:00
e0ea20bfb4
mtd: rawnand: lpc32xx_mlc: fix the probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup() and not
a nand_release(). The latter doing an mtd_device_unregister() which is
not needed if mtd_device_register() failed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:45 +02:00
838c07b05b
mtd: rawnand: lpc32xx_mlc: clean the probe function
Before fixing the error path of the probe function, fix the style of the
entire function and particularly the goto labels: they should indicate
what the next cleanup to do is.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:45 +02:00
ed64cb1df4
mtd: rawnand: hisi504: fix the probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup() and not
a nand_release(). The latter doing an mtd_device_unregister() which is
not needed if mtd_device_register() failed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:44 +02:00
6f533c4631
mtd: rawnand: hisi504: clean the probe function error path
There is not need for a goto statement when the only action to take is
to return.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:44 +02:00
9326dc754c
mtd: rawnand: fsmc: fix the probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:43 +02:00
682cae27b1
mtd: rawnand: fsmc: clean the probe function style
Before fixing the error path of the probe function, fix the style of the
probe function and mostly the goto labels: they should indicate what
the next cleanup is, not the point from which they can be accessed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:43 +02:00
43fab011e9
mtd: rawnand: fsl_ifc: fix probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

However, in this driver, fsl_ifc_chip_remove() which is called upon
error already triggers a nand_release() which is wrong, because a
nand_release() should be triggered only if an mtd_register() succeeded.

Move the nand_release() call out of the fsl_ifc_chip_remove() and put it
back in the *_remove() hook.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:43 +02:00
acfc33091f
mtd: rawnand: fsl_elbc: fix probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

However, in this driver, fsl_elbc_chip_remove() which is called upon
error already triggers a nand_release() which is wrong, because a
nand_release() should be triggered only if an mtd_register() succeeded.

Move the nand_release() call out of the fsl_elbc_chip_remove() and put
it back in the *_remove() hook.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-29 08:56:42 +02:00
39b77c586e
mtd: rawnand: mtk: use of_device_get_match_data()
The usage of of_device_get_match_data() reduce the code size a bit.

Also, the only way to call .probe() is to match an entry in
.of_match_table[], so of_device_id cannot be NULL.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Ryder Lee   authored and   Boris Brezillon   commited 2018-04-29 08:56:41 +02:00
36bf2eb90d
mtd: rawnand: diskonchip: Replace mdelay with usleep_range in doc_probe
doc_probe() is never called in atomic context.

doc_probe() is only called by init_nanddoc(), which is only set as
a parameter of module_init().
This function is not called in atomic context.

Despite never getting called from atomic context, doc_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Jia-Ju Bai   authored and   Boris Brezillon   commited 2018-04-29 08:56:41 +02:00
7b4b199459
mtd: rawnand: sunxi: Remove support for GPIO-based Ready/Busy polling
None of the existing platforms connect the R/B pin to a GPIO (they all
use one of the dedicated R/B pin).
Anyway, if we ever get short of native R/B pins, it's probably better
to fallback to STATUS reg polling than trying to poll a GPIO.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>

Boris Brezillon   commited 2018-04-29 08:56:41 +02:00
ddd5ed3a90
mtd: rawnand: gpmi: add support for specific ECC strength
Add support for specified ECC strength/size using device tree
properties nand-ecc-strength/nand-ecc-step-size.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Stefan Agner   authored and   Boris Brezillon   commited 2018-04-29 08:56:40 +02:00
6bf6ec522e
mtd: rawnand: davinci: don't acquire and enable clock
NAND itself is an asynchronous interface, it does not have any
clock input. DaVinci NAND driver acquires clock for AEMIF
(asynchronous external memory interface) which is an on-chip
IP to which NAND is connected.

The same clock is also enabled in AEMIF driver (either present
drivers/memory or from machine code for some older platforms).
AEMIF timing must be initialized before NAND can be accessed.
This ensures that AEMIF clock is enabled too.

Remove the superfluous clock acquisition and enable in DaVinci
NAND driver.

Tested on K2L, K2HK, K2E, DA850 EVM, DA850 LCDK in device-tree
boot and DM644x EVM in legacy boot.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Sekhar Nori   authored and   Boris Brezillon   commited 2018-04-26 19:55:40 +02:00
a8e3923ab5
mtd: rawnand: marvell: fix the chip-select DT parsing logic
The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
        1/ the actual condition to enter the sub-block and
        2/ the operation to do in this sub-block.

        [...]
        else if (condition1_to_enter && action1() == failed)
                raise_error();
        else if (condition2_to_enter && action2() == failed)
                raise_error();
        [...]

In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).

The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.

When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:

[    1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[    1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)

Indeed, this is harmless and the core will then assume there is only one
valid CS.

Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.

Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).

This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.

Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.

Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.

Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().

Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-04-26 19:06:42 +02:00
f6997bec6a
mtd: rawnand: diskonchip: Allocate rs control per instance
The reed solomon library is moving the on stack decoder buffers into the rs
control structure. That would break the DoC driver because multiple
instances share the same control structure and can operate in parallel. At
least in theory....

Instantiate a rs control instance per DoC device to avoid that. The per
instance buffer is fine as the operation on a single DoC instance is
serialized by the MTD/NAND core.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Andrew Morton <akpm@linuxfoundation.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Thomas Gleixner   authored and   Kees Cook   commited 2018-04-24 19:50:09 -07:00
964dfce9c2
rslib: Split rs control struct
The decoder library uses variable length arrays on stack. To get rid of
them it would be simple to allocate fixed length arrays on stack, but those
might become rather large. The other solution is to allocate the buffers in
the rs control structure, but this cannot be done as long as the structure
can be shared by several users. Sharing is desired because the RS polynom
tables are large and initialization is time consuming.

To solve this split the codec information out of the control structure and
have a pointer to a shared codec in it. Instantiate the control structure
for each user, create a new codec if no shareable is avaiable yet.  Adjust
all affected usage sites to the new scheme.

This allows to add per instance decoder buffers to the control structure
later on.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Andrew Morton <akpm@linuxfoundation.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Thomas Gleixner   authored and   Kees Cook   commited 2018-04-24 19:50:08 -07:00
2163398192
mtd: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Geert Uytterhoeven   authored and   Boris Brezillon   commited 2018-04-21 10:08:51 +02:00
7db782bc18
mtd: rawnand: tango: Fix struct clk memory leak
Use devm_clk_get() to let Linux manage struct clk memory.

Fixes: 6956e2385a ("add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Reported-by: Xidong Wang <wangxidong_97@163.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Marc Gonzalez   authored and   Boris Brezillon   commited 2018-04-21 00:24:57 +02:00
007b4e8b70
MTD changes:
Core:
     * Remove support for asynchronous erase (not implemented by any of
       the existing drivers anyway)
     * Remove Cyrille from the list of SPI NOR and MTD maintainers
     * Fix kernel doc headers
     * Allow users to define the partitions parsers they want to test
       through a DT property (compatible of the partitions subnode)
     * Remove the bfin-async-flash driver (the only architecture using
       it has been removed)
     * Fix pagetest test
     * Add extra checks in mtd_erase()
     * Simplify the MTD partition creation logic and get rid of
       mtd_add_device_partitions()
 
    Drivers:
     * Add endianness information to the physmap DT binding
     * Add Eon EN29LV400A IDs to JEDEC probe logic
     * Use %*ph where appropriate
 
 SPI NOR changes:
   Drivers:
     * Make fsl-quaspi assign different names to MTD devices connected
       to the same QSPI controller
     * Remove an unneeded driver.bus assigned in the fsl-qspi driver
 
 NAND changes:
   Core:
     * Prepare arrival of the SPI NAND subsystem by implementing a
       generic (interface-agnostic) layer to ease manipulation of NAND
       devices
     * Move onenand code base to the drivers/mtd/nand/ dir
     * Rework timing mode selection
     * Provide a generic way for NAND chip drivers to flag a specific
       GET/SET FEATURE operation as supported/unsupported
     * Stop embedding ONFI/JEDEC param page in nand_chip
 
   Drivers:
     * Rework/cleanup of the mxc driver
     * Various cleanups in the vf610 driver
     * Migrate the fsmc and vf610 to ->exec_op()
     * Get rid of the pxa driver (replaced by marvell_nand)
     * Support ->setup_data_interface() in the GPMI driver
     * Fix probe error path in several drivers
     * Remove support for unused hw_syndrome mode in sunxi_nand
     * Various minor improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQI5BAABCAAjBQJaxTXfHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
 Ze02AX4ItwDeFhAAs+OmGip0LHk+D7gFCBONtypOGRi0nmGsi6PkhKtUZBob6/Y2
 JoJhTrHx/LsRpqcuh3Y8KSCp0CG5WlZX2m1RU1yrcqiWvTfiXHlv6aQGfiE/esRb
 Ei4QNiND8hg+hyzc6I5wRrAuJ7jPP5BanX+n9TyvygaA1Ic5pcur0gssoYKeJTia
 18pUV+RLe67wfP02uT0GJvmXd5ecIpu0OVhmJPye2UQqnfl+eiJ2zI4TJAZN3zRW
 tD9XiX3/GP8oCnvC+1kZw48a2c/qiHs/DKCdDcH6SDTKzKha4zCgaX4220X3AqPK
 rScrFTKxiCa1utZPn9EplnW6ZW3Ud46GqReWGRQZuyphu/ntdkNim7nuJMUZfEFL
 RFtMLhXDs1aXUaYJ6F3YQeajHxVU6Ugl34UQCraCXbfmzqCkaKfgXm3EVb9d2duY
 rCkrS5N4gSQXp5SMvc0aiu2TnsRX2OCthGg0NBdHG9AaVhwuj0neeSFQ/XFPxOeh
 5jQKo4umR7tr2Md7osSx0PVxVo8uO5smqcl90SsdwrjxQxL7z1u/SJBjRf6pJDzQ
 cR1o+H9jBXecqD6m+dN3H/h0sMwHzefsASkxYNxl2OeRGYsJvBpuoQF8yUD9jnRS
 AzHhWhUNo8g3FxDe7kKgsMXoqnr/pKopMCRxVbeEkhDFNsTvBde10/Xo09U=
 =EG7L
 -----END PGP SIGNATURE-----

Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd

Pull MTD updates from Boris Brezillon:
 "MTD Core:
   - Remove support for asynchronous erase (not implemented by any of
     the existing drivers anyway)
   - Remove Cyrille from the list of SPI NOR and MTD maintainers
   - Fix kernel doc headers
   - Allow users to define the partitions parsers they want to test
     through a DT property (compatible of the partitions subnode)
   - Remove the bfin-async-flash driver (the only architecture using it
     has been removed)
   - Fix pagetest test
   - Add extra checks in mtd_erase()
   - Simplify the MTD partition creation logic and get rid of
     mtd_add_device_partitions()

  MTD Drivers:
   - Add endianness information to the physmap DT binding
   - Add Eon EN29LV400A IDs to JEDEC probe logic
   - Use %*ph where appropriate

  SPI NOR Drivers:
   - Make fsl-quaspi assign different names to MTD devices connected to
     the same QSPI controller
   - Remove an unneeded driver.bus assigned in the fsl-qspi driver

  NAND Core:
   - Prepare arrival of the SPI NAND subsystem by implementing a generic
     (interface-agnostic) layer to ease manipulation of NAND devices
   - Move onenand code base to the drivers/mtd/nand/ dir
   - Rework timing mode selection
   - Provide a generic way for NAND chip drivers to flag a specific
     GET/SET FEATURE operation as supported/unsupported
   - Stop embedding ONFI/JEDEC param page in nand_chip

  NAND Drivers:
   - Rework/cleanup of the mxc driver
   - Various cleanups in the vf610 driver
   - Migrate the fsmc and vf610 to ->exec_op()
   - Get rid of the pxa driver (replaced by marvell_nand)
   - Support ->setup_data_interface() in the GPMI driver
   - Fix probe error path in several drivers
   - Remove support for unused hw_syndrome mode in sunxi_nand
   - Various minor improvements"

* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
  dt-bindings: fsl-quadspi: Add the example of two SPI NOR
  mtd: fsl-quadspi: Distinguish the mtd device names
  mtd: nand: Fix some function description mismatches in core.c
  mtd: fsl-quadspi: Remove unneeded driver.bus assignment
  mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
  mtd: rawnand: s3c2410: enhance the probe function error path
  mtd: rawnand: tango: fix probe function error path
  mtd: rawnand: sh_flctl: fix the probe function error path
  mtd: rawnand: omap2: fix the probe function error path
  mtd: rawnand: mxc: fix probe function error path
  mtd: rawnand: denali: fix probe function error path
  mtd: rawnand: davinci: fix probe function error path
  mtd: rawnand: cafe: fix probe function error path
  mtd: rawnand: brcmnand: fix probe function error path
  mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
  mtd: rawnand: marvell: Fix clock resource by adding a register clock
  mtd: ftl: Use DIV_ROUND_UP()
  mtd: Fix some function description mismatches in mtdcore.c
  mtd: physmap_of: update struct map_info's swap as per map requirement
  dt-bindings: mtd-physmap: Add endianness supports
  ...

Linus Torvalds   commited 2018-04-06 12:15:41 -07:00
3fd14cdcc0
Linux 4.16-rc2
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqKKI0eHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGRNAH/0v3+nuJ0oiHE1Cl
 fH89F9Ma17j8oTo28byRPi7X5XJfJAqANhHa209rguvnC27y3ew/l9k93HoxG12i
 ttvyKFDQulQbytfJZXw8lhUyYGXVsTpyNaihPe/NtqPdIxNgfrXsUN9EIEtcnuS2
 SiAj51jUySDRNR4ST6TOx4ulDm1zLrmA28WHOBNOTvDi4jTQMt1TsngHfF5AySBB
 lD4RTRDDwWDWtdMI7euYSq019TiDXCxmwQ94vZjrqmjmSQcl/yCK/JzEV33SZslg
 4WqGIllxONvP/UlwxZLaJ+RrslqxNgDVqQKwJdfYhGaWvpgPFtS1s86zW6IgyXny
 02jJfD0=
 =DLWn
 -----END PGP SIGNATURE-----

Merge tag 'v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mtd/next

Backmerge v4.16-rc2 into mtd/next to resolve a conflict between Linus'
master branch and nand/for-4.17.

Boris Brezillon   commited 2018-04-04 22:13:35 +02:00
fe5f31a801
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
   (interface-agnostic) layer to ease manipulation of NAND devices
 * Move onenand code base to the drivers/mtd/nand/ dir
 * Rework timing mode selection
 * Provide a generic way for NAND chip drivers to flag a specific
   GET/SET FEATURE operation as supported/unsupported
 * Stop embedding ONFI/JEDEC param page in nand_chip
 
 Driver changes:
 * Rework/cleanup of the mxc driver
 * Various cleanups in the vf610 driver
 * Migrate the fsmc and vf610 to ->exec_op()
 * Get rid of the pxa driver (replaced by marvell_nand)
 * Support ->setup_data_interface() in the GPMI driver
 * Fix probe error path in several drivers
 * Remove support for unused hw_syndrome mode in sunxi_nand
 * Various minor improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQI5BAABCAAjBQJavURPHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
 Ze02AX4ItwDzsw//YqnrDG6JzEBGEEJ0c1I6O/2Zk9eDrXhDeKk2S4G292QGQ4by
 8bKYpHo3al9TxTBb/to6+BexoP717tSwbn+AcW5W2YqGpIAeSGaw1POGau9E7l71
 wQh1aECOXCpLVLKbv/JFspiKMJYj+irxoTjdR6/3FjawDx0ruLwCCLlvOFlfkUOM
 ESv+hZv9364jcq/SsydYTYaIc95IsfBOUZVYcXRRdtaI7hvD9ljfXRSGNh+Guovc
 Bmvyiv9VuUBRg/v26gdQjESVfs3k37YV6LfS5eQSPuCHs2WGaZa5S6mBpHunAxTN
 bhbd+vVwzMaDSmX29Xsml+isJnmTdBBJRcg4qusY/nBjeUHtY2nj5J3bq+CuhSwj
 q2MB6YyBStqeagzBvctt3wzG9S7ZsVGU+PMtpMkH4T8BY+Bff9yFCPmRZwTUOorK
 iVuVhS2NImvJZ05/hc9VchAmSqd4PozHM08oW0NC6FqnF63hinkzw0J3K6FXycFF
 q/6lioZFHE8qJbD3LhDqCrLJoRDQDpxVQmZP9RCL1iozW7GNIYD7/IrPrsgqSQNa
 P10PvPt8lbBNq3GU3mIMtajTVihRJmH4Kdxd2i08dRp4hxIakF9Zx3MOhw5gZc0b
 C0xoFgaEvxbyb5P3VGVy7LYTvTfvJ9KsacntTSn7LrIU3D7meXmwnHynq5A=
 =uvio
 -----END PGP SIGNATURE-----

Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next

Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
  (interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
  GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip

Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements

Boris Brezillon   commited 2018-04-04 22:11:36 +02:00
a88b5f3833
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
The core clock field was badly named ->ecc_clk which might lead to some
confusion. Rename it ->core_clk.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>

Boris Brezillon   commited 2018-03-29 09:38:21 +02:00
6b6de6543d
mtd: rawnand: s3c2410: enhance the probe function error path
Prepare the migration of the lpc32xx_slc driver to use nand_scan() by
cleaning the error path in the probe function.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-29 09:38:21 +02:00
bb00ff2f4a
mtd: rawnand: tango: fix probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-29 09:38:20 +02:00
0eaa879be6
mtd: rawnand: sh_flctl: fix the probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-29 09:38:20 +02:00
5a3e8cde10
mtd: rawnand: omap2: fix the probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-29 09:38:20 +02:00
122bb3cb8b
mtd: rawnand: mxc: fix probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-29 09:38:19 +02:00
be051bf28f
mtd: rawnand: denali: fix probe function error path
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-29 09:38:19 +02:00
4e5d1d9078