Watch
1
0
Fork
You've already forked kernel_a52xq
0
mirror of https://github.com/a52xq-dev/kernel.git synced 2026-11-22 01:46:57 +07:00
Commit graph kernel_a52xq/drivers/mtd/nand/raw/nand_timings.c
Message SHA1
mtd: rawnand: allocate dynamically ONFI parameters during detection
Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   commited 2018-08-01 09:45:59 +02:00
3d3fe3c05d
mtd: rawnand: add default values for dynamic timings
Some timings like tBERS (block erase time), tCCs (change column setup
time), tPROG (page program time) and tR (page read time) are derived
from the ONFI parameter page. They are set in the SDR interface only
if the chip is ONFI compliant.

It makes these timings unreliable and prevent the driver to use one of
these four values with a non-ONFI chip.

Fix this situation by taking the highest possible value (or a default
one) value for each missing timing (stored as unsigned 16-bit entries in
the parameter page).

This makes tBERS and tPROG being ~65ms while typical values are at most
a few milliseconds. As these are timeouts, it is not impacting at all
the performances in nominal use.

tR maximum time and tCCS minimum time (delay to wait after a change
column) are set, according to the ONFI specification, to default 'slow'
values; respectively 200us and 500ns.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Miquel Raynal   commited 2018-07-19 23:14:13 +02:00
6a943386ee
mtd: rawnand: prepare the removal of the ONFI parameter page
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.

ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.

For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Miquel Raynal   authored and   Boris Brezillon   commited 2018-03-20 11:59:54 +01:00
a97421c753
mtd: nand: move raw NAND related code to the raw/ subdir
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

Boris Brezillon   commited 2018-02-16 10:09:34 +01:00
93db446a42
Renamed from drivers/mtd/nand/nand_timings.c (Browse further)