mirror of
https://github.com/a52xq-dev/kernel.git
synced 2026-11-22 01:46:57 +07:00
| Message | SHA1 | |
|---|---|---|
mtd: rawnand: marvell: prevent timeouts on a loaded machine
commit cafb56dd741e61c99709bcd2b193a9a1d36def3b upstream.
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes:
|
5cad883fd6 | |
mtd: rawnand: marvell: fix the IRQ handler complete() condition
commit 53c83b59759c1ee213f5ffa194909daee8902a28 upstream.
With the current implementation, the complete() in the IRQ handler is
supposed to be called only if the register status has one or the other
RDY bit set. Other events might trigger an interrupt as well if
enabled, but should not end-up with a complete() call.
For this purpose, the code was checking if the other bits were set, in
this case complete() was not called. This is wrong as two events might
happen in a very tight time-frame and if the NDSR status read reports
two bits set (eg. RDY(0) and RDDREQ) at the same time, complete() was
not called.
This logic would lead to timeouts in marvell_nfc_wait_op() and has
been observed on PXA boards (NFCv1) in the Hamming write path.
Fixes:
|
6737137331 | |
mtd: rawnand: marvell: prevent harmless warnings
Since the addition of WARN_ON() in nand_subop_get_data/addr_len()
helpers, this driver will produce harmless warnings (mostly at probe)
just because it always calls the nand_subop_get_data_len() helper in
the parsing function (even on non-data instructions, where this value
is meaningless and unneeded).
Fix these warnings by deriving the length only when it is relevant.
Fixes:
|
21a2680692 | |
sound updates for 4.19
It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer;
also offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types
-----BEGIN PGP SIGNATURE-----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=eTIC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
|
747f62305d | |
mtd: rawnand: marvell: convert driver to nand_scan()
Two helpers have been added to the core to do all kind of controller side configuration/initialization between the detection phase and the final NAND scan. Implement these hooks so that we can convert the driver to just use nand_scan() instead of the nand_scan_ident() + nand_scan_tail() pair. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> |
8831e48bad | |
mtd: rawnand: better name for the controller structure
In the raw NAND core, a NAND chip is described by a nand_chip structure, while a NAND controller is described with a nand_hw_control structure which is not very meaningful. Rename this structure nand_controller. As the structure gets renamed, it is logical to also rename the core function initializing it from nand_hw_control_init() to nand_controller_init(). Lastly, the 'hwcontrol' entry of the nand_chip structure is not meaningful neither while it has the role of fallback when no controller structure is provided by the driver (the controller driver is dumb and can only control a single chip). Thus, it is renamed dummy_controller. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> |
7da45139d2 | |
mtd: rawnand: marvell: set reg_clk to NULL if it can't be obtained
Don't keep an error-pointer around in the private struct. If this optional clock can't be obtained, simply set the pointer to NULL instead so we can use clk_prepare_enable() on it without further checks, Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> |
f9e64d6104 | |
mtd: rawnand: marvell: remove bogus comment in marvell_nfc_select_chip()
The comment in marvell_nfc_select_chip() about ndtr0 and ndtr1 didn't reflect what the driver was doing. The values of NDTR0 and NDTR1 are read from the registers at probe time and a copy is retained in 'struct marvell_nand_chip'. If keep-config is set in the DT properties, there are no other writers of these timing variables so they can safely be used when the chip is selected. As suggested by Miquel Raynal, simply remove the comment. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> |
7734a275a7 | |
mtd: rawnand: marvell: add suspend and resume hooks
This patch restores the suspend and resume hooks that the old driver used
to have. Apart from stopping and starting the clocks, the resume callback
also nullifies the selected_chip pointer, so the next command that is issued
will re-select the chip and thereby restore the timing registers.
Factor out some code from marvell_nfc_init() into a new function
marvell_nfc_reset() and also call it at resume time to reset some registers
that don't retain their contents during low-power mode.
Without this patch, a PXA3xx based system would cough up an error similar to
the one below after resume.
[ 44.660162] marvell-nfc 43100000.nand-controller: Timeout waiting for RB signal
[ 44.671492] ubi0 error: ubi_io_write: error -110 while writing 2048 bytes to PEB 102:38912, written 0 bytes
[ 44.682887] CPU: 0 PID: 1417 Comm: remote-control Not tainted 4.18.0-rc2+ #344
[ 44.691197] Hardware name: Marvell PXA3xx (Device Tree Support)
[ 44.697111] Backtrace:
[ 44.699593] [<c0106458>] (dump_backtrace) from [<c0106718>] (show_stack+0x18/0x1c)
[ 44.708931] r7:00000800 r6:00009800 r5:00000066 r4:c6139000
[ 44.715833] [<c0106700>] (show_stack) from [<c0678a60>] (dump_stack+0x20/0x28)
[ 44.724206] [<c0678a40>] (dump_stack) from [<c0456cbc>] (ubi_io_write+0x3d4/0x630)
[ 44.732925] [<c04568e8>] (ubi_io_write) from [<c0454428>] (ubi_eba_write_leb+0x690/0x6fc)
...
Fixes:
|
bd9c3f9b3c | |
mtd: rawnand: marvell: Handle on-die ECC
>From the controllers point of view this is the same as no or software only ECC. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> |
ed6d0285f8 | |
mtd: rawnand: marvell: remove the dmaengine compat need
As the pxa architecture switched towards the dmaengine slave map, the old compatibility mechanism to acquire the dma requestor line number and priority are not needed anymore. This patch simplifies the dma resource acquisition, using the more generic function dma_request_slave_channel(). Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> |
ac75a50b6d | |
mtd: rawnand: marvell: Fix read logic for layouts with ->nchunks > 2
The code is doing monolithic reads for all chunks except the last one
which is wrong since a monolithic read will issue the
READ0+ADDRS+READ_START sequence. It not only takes longer because it
forces the NAND chip to reload the page content into its internal
cache, but by doing that we also reset the column pointer to 0, which
means we'll always read the first chunk instead of moving to the next
one.
Rework the code to do a monolithic read only for the first chunk,
then switch to naked reads for all intermediate chunks and finally
issue a last naked read for the last chunk.
Fixes:
|
90d6176333 | |
mtd: rawnand: marvell: fix command xtype in BCH write hook
One layout supported by the Marvell NAND controller supports NAND pages
of 2048 bytes, all handled in one single chunk when using BCH with a
strength of 4-bit per 512 bytes. In this case, instead of the generic
XTYPE_WRITE_DISPATCH/XTYPE_LAST_NAKED_RW couple, the controller expects
to receive XTYPE_MONOLITHIC_RW.
This fixes problems at boot like:
[ 1.315475] Scanning device for bad blocks
[ 3.203108] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 3.209564] nand_bbt: error while writing BBT block -110
[ 4.243106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 5.283106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 5.289562] nand_bbt: error -110 while marking block 2047 bad
[ 6.323106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 6.329559] nand_bbt: error while writing BBT block -110
[ 7.363106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 8.403105] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 8.409559] nand_bbt: error -110 while marking block 2046 bad
...
Fixes:
|
a2ee41fd95 | |
mtd: rawnand: marvell: pass ms delay to wait_op
marvell_nfc_wait_op() expects the delay to be expressed in milliseconds
but nand_sdr_timings uses picoseconds. Use PSEC_TO_MSEC when passing
tPROG_max to marvell_nfc_wait_op().
Fixes:
|
b76401fc4b | |
mtd: rawnand: marvell: fix the chip-select DT parsing logic
The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
1/ the actual condition to enter the sub-block and
2/ the operation to do in this sub-block.
[...]
else if (condition1_to_enter && action1() == failed)
raise_error();
else if (condition2_to_enter && action2() == failed)
raise_error();
[...]
In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).
The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.
When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:
[ 1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[ 1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)
Indeed, this is harmless and the core will then assume there is only one
valid CS.
Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.
Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).
This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.
Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.
Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.
Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().
Fixes:
|
f6997bec6a | |
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
The core clock field was badly named ->ecc_clk which might lead to some confusion. Rename it ->core_clk. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> |
6b6de6543d | |
mtd: rawnand: marvell: Fix clock resource by adding a register clock
On Armada 7K/8K we need to explicitly enable the register clock. This clock is optional because not all the SoCs using this IP need it but at least for Armada 7K/8K it is actually mandatory. The binding documentation is updated accordingly. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> |
961ba15c48 | |
Remove the pxa3xx_nand driver (replaced by marvell_nand).
-----BEGIN PGP SIGNATURE----- iQI5BAABCAAjBQJamceNHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ Ze02AX4ItwAkoxAAtdrbc5so/m0ZgPxVkoPl+d3cO+1KveG+OD4kvydieuKZmfGx htfayfAG47GsutoN5yXEeuCh5BLkhGsjaBFPO9RhxZM+dZUPl2s3Dp7H/m5xMkaA DrYMZ2AQE+Ll4YUaAFE7CIZ9dOwXjHG4rI2wAPRZ+tjs6okmiTP7luYnn4kGwqbC qgEmpjxawWl+LwujJqu4ilz4HLe/1zmE7BxGUeUqhyUXnwfgtVTmZVglMKPambZt i5Qqom3NOY2qXXdc/ONsYhdwUwLeR1v5Sz0FJw2vpxKKpXPl18SCmxzVuefOxvix n6Z0BnKTt+vSPMAZuGkkvr559/jHNT5EQnN5K7TXzl5V4K84HSUWhXHNi4SwZce+ ASTgOPJUvq/h0Mwo9nC+c7XUQnZ1FjYOY981gDs8XyM5WdA4TpN4TJmhgzUQX59q +Ui+vQ+0FVNIXmqZ+qqxnZ/wRVzlPgCDTLKLl4goZ+u9EU2LXvkeoOz0k1mEQ1Pd ehSfFZSdfSKkXxzb52R3JV6ELZ9POh66u2abf35mWIgC+l1gApFWpqIdIb3i/Wko ALuaLu3k9SnrZgiEuJy9yQ/qKD6pydyfpM2YgO/XEhtRxDlamLWOMyLmgcA1Z/gM oYhr5v3leNu3Dyd3RWLQXFRMe1qmUugmxvvbNyh8BhX9r2PmUhuiTdcFf6U= =bovT -----END PGP SIGNATURE----- Merge tag 'nand/pxa3xx-removal' of git://git.infradead.org/linux-mtd into nand/next Remove the pxa3xx_nand driver (replaced by marvell_nand). |
3383fb35c9 | |
mtd: nand: move raw NAND related code to the raw/ subdir
As part of the process of sharing more code between different NAND based devices, we need to move all raw NAND related code to the raw/ subdirectory. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> |
93db446a42 |
Renamed from drivers/mtd/nand/marvell_nand.c (Browse further)