mirror of
https://github.com/a52xq-dev/kernel.git
synced 2026-10-18 21:58:11 +07:00
| SHA1 | ||
|---|---|---|
* this imports the latest version of SM-A526B kernel from https://opensource.samsung.com/uploadSearch?searchValue=SM-A526B |
34794f4cb2
|
|
commit 8746f135bb01872ff412d408ea1aa9ebd328c1f5 upstream.
E0 is not allowed with Level 4:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part C page 1319:
'128-bit equivalent strength for link and encryption keys
required using FIPS approved algorithms (E0 not allowed,
SAFER+ not allowed, and P-192 not allowed; encryption key
not shortened'
SC enabled:
> HCI Event: Read Remote Extended Features (0x23) plen 13
Status: Success (0x00)
Handle: 256
Page: 1/2
Features: 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Secure Simple Pairing (Host Support)
LE Supported (Host)
Secure Connections (Host Support)
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 256
Encryption: Enabled with AES-CCM (0x02)
SC disabled:
> HCI Event: Read Remote Extended Features (0x23) plen 13
Status: Success (0x00)
Handle: 256
Page: 1/2
Features: 0x03 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Secure Simple Pairing (Host Support)
LE Supported (Host)
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 256
Encryption: Enabled with E0 (0x01)
[May 8 20:23] Bluetooth: hci0: Invalid security: expect AES but E0 was used
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 256
Reason: Authentication Failure (0x05)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Hans-Christian Noren Egtvedt <hegtvedt@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luiz Augusto von Dentz
authored and
 Greg Kroah-Hartman
commited |
c1ad9bb3b0 | |
commit 3ca44c16b0dcc764b641ee4ac226909f5c421aa3 upstream. This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection state is BT_CONFIG so callers don't have to check the state. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: Hans-Christian Noren Egtvedt <hegtvedt@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luiz Augusto von Dentz
authored and
Greg Kroah-Hartman
commited |
0c75831bc1 | |
commit b560a208cda0297fef6ff85bbfd58a8f0a52a543 upstream. This checks if BT_HS is enabled relecting it on MGMT_SETTING_HS instead of always reporting it as supported. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luiz Augusto von Dentz
authored and
Greg Kroah-Hartman
commited |
7b2e80606a | |
commit f19425641cb2572a33cb074d5e30283720bd4d22 upstream. Only sockets will have the chan->data set to an actual sk, channels like A2MP would have its own data which would likely cause a crash when calling sk_filter, in order to fix this a new callback has been introduced so channels can implement their own filtering if necessary. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luiz Augusto von Dentz
authored and
Greg Kroah-Hartman
commited |
360f80e342 | |
commit eddb7732119d53400f48a02536a84c509692faa8 upstream. This fixes various places where a stack variable is used uninitialized. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luiz Augusto von Dentz
authored and
Greg Kroah-Hartman
commited |
128278f444 | |
[ Upstream commit adf1d6926444029396861413aba8a0f2a805742a ]
After sending Inquiry Cancel command to the controller, it is possible
that Inquiry Complete event comes before Inquiry Cancel command complete
event. In this case the Inquiry Cancel command will have status of
Command Disallowed since there is no Inquiry session to be cancelled.
This case should not be treated as error, otherwise we can reach an
inconsistent state.
Example of a btmon trace when this happened:
< HCI Command: Inquiry Cancel (0x01|0x0002) plen 0
> HCI Event: Inquiry Complete (0x01) plen 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4
Inquiry Cancel (0x01|0x0002) ncmd 1
Status: Command Disallowed (0x0c)
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sonny Sasaka
authored and
Greg Kroah-Hartman
commited |
f3fd4552a9 | |
[ Upstream commit 96298f640104e4cd9a913a6e50b0b981829b94ff ] According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state. The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change. === Before === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 #22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 #23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 #24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 #27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 #28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 #29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 #30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 #31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ...... < ACL Data TX: Handle 256 flags 0x00 dlen 14 #32 L2CAP: Command Reject (0x01) ident 3 len 6 Reason: Invalid CID in request (0x0002) Destination CID: 64 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #33 Num handles: 1 Handle: 256 Count: 1 ... === After === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 #22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 #23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 #24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 #27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 #28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 #29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 #30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 #31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ..... < ACL Data TX: Handle 256 flags 0x00 dlen 18 #32 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 < ACL Data TX: Handle 256 flags 0x00 dlen 12 #33 L2CAP: Configure Request (0x04) ident 3 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 #34 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #35 Num handles: 1 Handle: 256 Count: 1 ... Signed-off-by: Howard Chung <howardchung@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Howard Chung
authored and
Greg Kroah-Hartman
commited |
8828622fb9 | |
[ Upstream commit 08bb4da90150e2a225f35e0f642cdc463958d696 ] Some controllers have been observed to send zero'd events under some conditions. This change guards against this condition as well as adding a trace to facilitate diagnosability of this condition. Signed-off-by: Alain Michaud <alainm@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Alain Michaud
authored and
Greg Kroah-Hartman
commited |
1ee3da6b96 | |
[ Upstream commit 2a154903cec20fb64ff4d7d617ca53c16f8fd53a ] Prefetch channel before killing sock in order to fix UAF like BUG: KASAN: use-after-free in l2cap_sock_release+0x24c/0x290 net/bluetooth/l2cap_sock.c:1212 Read of size 8 at addr ffff8880944904a0 by task syz-fuzzer/9751 Reported-by: syzbot+c3c5bdea7863886115dc@syzkaller.appspotmail.com Fixes: 6c08fc896b60 ("Bluetooth: Fix refcount use-after-free issue") Cc: Manish Mandlik <mmandlik@google.com> Signed-off-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Hillf Danton
authored and
Greg Kroah-Hartman
commited |
4b0795d5b6 | |
[ Upstream commit 6c08fc896b60893c5d673764b0668015d76df462 ] There is no lock preventing both l2cap_sock_release() and chan->ops->close() from running at the same time. If we consider Thread A running l2cap_chan_timeout() and Thread B running l2cap_sock_release(), expected behavior is: A::l2cap_chan_timeout()->l2cap_chan_close()->l2cap_sock_teardown_cb() A::l2cap_chan_timeout()->l2cap_sock_close_cb()->l2cap_sock_kill() B::l2cap_sock_release()->sock_orphan() B::l2cap_sock_release()->l2cap_sock_kill() where, sock_orphan() clears "sk->sk_socket" and l2cap_sock_teardown_cb() marks socket as SOCK_ZAPPED. In l2cap_sock_kill(), there is an "if-statement" that checks if both sock_orphan() and sock_teardown() has been run i.e. sk->sk_socket is NULL and socket is marked as SOCK_ZAPPED. Socket is killed if the condition is satisfied. In the race condition, following occurs: A::l2cap_chan_timeout()->l2cap_chan_close()->l2cap_sock_teardown_cb() B::l2cap_sock_release()->sock_orphan() B::l2cap_sock_release()->l2cap_sock_kill() A::l2cap_chan_timeout()->l2cap_sock_close_cb()->l2cap_sock_kill() In this scenario, "if-statement" is true in both B::l2cap_sock_kill() and A::l2cap_sock_kill() and we hit "refcount: underflow; use-after-free" bug. Similar condition occurs at other places where teardown/sock_kill is happening: l2cap_disconnect_rsp()->l2cap_chan_del()->l2cap_sock_teardown_cb() l2cap_disconnect_rsp()->l2cap_sock_close_cb()->l2cap_sock_kill() l2cap_conn_del()->l2cap_chan_del()->l2cap_sock_teardown_cb() l2cap_conn_del()->l2cap_sock_close_cb()->l2cap_sock_kill() l2cap_disconnect_req()->l2cap_chan_del()->l2cap_sock_teardown_cb() l2cap_disconnect_req()->l2cap_sock_close_cb()->l2cap_sock_kill() l2cap_sock_cleanup_listen()->l2cap_chan_close()->l2cap_sock_teardown_cb() l2cap_sock_cleanup_listen()->l2cap_sock_kill() Protect teardown/sock_kill and orphan/sock_kill by adding hold_lock on l2cap channel to ensure that the socket is killed only after marked as zapped and orphan. Signed-off-by: Manish Mandlik <mmandlik@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Manish Mandlik
authored and
Greg Kroah-Hartman
commited |
3b73af6cb9 | |
[ Upstream commit f9c70bdc279b191da8d60777c627702c06e4a37d ] In the case we set or free the global value listen_chan in different threads, we can encounter the UAF problems because the method is not protected by any lock, add one to avoid this bug. BUG: KASAN: use-after-free in l2cap_chan_close+0x48/0x990 net/bluetooth/l2cap_core.c:730 Read of size 8 at addr ffff888096950000 by task kworker/1:102/2868 CPU: 1 PID: 2868 Comm: kworker/1:102 Not tainted 5.5.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: events do_enable_set Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1fb/0x318 lib/dump_stack.c:118 print_address_description+0x74/0x5c0 mm/kasan/report.c:374 __kasan_report+0x149/0x1c0 mm/kasan/report.c:506 kasan_report+0x26/0x50 mm/kasan/common.c:641 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:135 l2cap_chan_close+0x48/0x990 net/bluetooth/l2cap_core.c:730 do_enable_set+0x660/0x900 net/bluetooth/6lowpan.c:1074 process_one_work+0x7f5/0x10f0 kernel/workqueue.c:2264 worker_thread+0xbbc/0x1630 kernel/workqueue.c:2410 kthread+0x332/0x350 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Allocated by task 2870: save_stack mm/kasan/common.c:72 [inline] set_track mm/kasan/common.c:80 [inline] __kasan_kmalloc+0x118/0x1c0 mm/kasan/common.c:515 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:529 kmem_cache_alloc_trace+0x221/0x2f0 mm/slab.c:3551 kmalloc include/linux/slab.h:555 [inline] kzalloc include/linux/slab.h:669 [inline] l2cap_chan_create+0x50/0x320 net/bluetooth/l2cap_core.c:446 chan_create net/bluetooth/6lowpan.c:640 [inline] bt_6lowpan_listen net/bluetooth/6lowpan.c:959 [inline] do_enable_set+0x6a4/0x900 net/bluetooth/6lowpan.c:1078 process_one_work+0x7f5/0x10f0 kernel/workqueue.c:2264 worker_thread+0xbbc/0x1630 kernel/workqueue.c:2410 kthread+0x332/0x350 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Freed by task 2870: save_stack mm/kasan/common.c:72 [inline] set_track mm/kasan/common.c:80 [inline] kasan_set_free_info mm/kasan/common.c:337 [inline] __kasan_slab_free+0x12e/0x1e0 mm/kasan/common.c:476 kasan_slab_free+0xe/0x10 mm/kasan/common.c:485 __cache_free mm/slab.c:3426 [inline] kfree+0x10d/0x220 mm/slab.c:3757 l2cap_chan_destroy net/bluetooth/l2cap_core.c:484 [inline] kref_put include/linux/kref.h:65 [inline] l2cap_chan_put+0x170/0x190 net/bluetooth/l2cap_core.c:498 do_enable_set+0x66c/0x900 net/bluetooth/6lowpan.c:1075 process_one_work+0x7f5/0x10f0 kernel/workqueue.c:2264 worker_thread+0xbbc/0x1630 kernel/workqueue.c:2410 kthread+0x332/0x350 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 The buggy address belongs to the object at ffff888096950000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 0 bytes inside of 2048-byte region [ffff888096950000, ffff888096950800) The buggy address belongs to the page: page:ffffea00025a5400 refcount:1 mapcount:0 mapping:ffff8880aa400e00 index:0x0 flags: 0xfffe0000000200(slab) raw: 00fffe0000000200 ffffea00027d1548 ffffea0002397808 ffff8880aa400e00 raw: 0000000000000000 ffff888096950000 0000000100000001 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88809694ff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88809694ff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888096950000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888096950080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888096950100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Reported-by: syzbot+96414aa0033c363d8458@syzkaller.appspotmail.com Signed-off-by: Lihong Kou <koulihong@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Lihong Kou
authored and
Greg Kroah-Hartman
commited |
29e1dfcd51 | |
commit 629b49c848ee71244203934347bd7730b0ddee8d upstream. Check `num_rsp` before using it as for-loop counter. Add `unlock` label. Cc: stable@vger.kernel.org Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Peilin Ye
authored and
Greg Kroah-Hartman
commited |
48f70ecd6a | |
commit 75bbd2ea50ba1c5d9da878a17e92eac02fe0fd3a upstream. Check `num_rsp` before using it as for-loop counter. Cc: stable@vger.kernel.org Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peilin Ye
authored and
Greg Kroah-Hartman
commited |
f2d6adb023 | |
commit 51c19bf3d5cfaa66571e4b88ba2a6f6295311101 upstream.
Check upon `num_rsp` is insufficient. A malformed event packet with a
large `num_rsp` number makes hci_extended_inquiry_result_evt() go out
of bounds. Fix it.
This patch fixes the following syzbot bug:
https://syzkaller.appspot.com/bug?id=4bf11aa05c4ca51ce0df86e500fce486552dc8d2
Reported-by: syzbot+d8489a79b781849b9c46@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peilin Ye
authored and
Greg Kroah-Hartman
commited |
8c4a649c20 | |
[ Upstream commit a2ec905d1e160a33b2e210e45ad30445ef26ce0e ]
Fix kernel oops observed when an ext adv data is larger than 31 bytes.
This can be reproduced by setting up an advertiser with advertisement
larger than 31 bytes. The issue is not sensitive to the advertisement
content. In particular, this was reproduced with an advertisement of
229 bytes filled with 'A'. See stack trace below.
This is fixed by not catching ext_adv as legacy adv are only cached to
be able to concatenate a scanable adv with its scan response before
sending it up through mgmt.
With ext_adv, this is no longer necessary.
general protection fault: 0000 [#1] SMP PTI
CPU: 6 PID: 205 Comm: kworker/u17:0 Not tainted 5.4.0-37-generic #41-Ubuntu
Hardware name: Dell Inc. XPS 15 7590/0CF6RR, BIOS 1.7.0 05/11/2020
Workqueue: hci0 hci_rx_work [bluetooth]
RIP: 0010:hci_bdaddr_list_lookup+0x1e/0x40 [bluetooth]
Code: ff ff e9 26 ff ff ff 0f 1f 44 00 00 0f 1f 44 00 00 55 48 8b 07 48 89 e5 48 39 c7 75 0a eb 24 48 8b 00 48 39 f8 74 1c 44 8b 06 <44> 39 40 10 75 ef 44 0f b7 4e 04 66 44 39 48 14 75 e3 38 50 16 75
RSP: 0018:ffffbc6a40493c70 EFLAGS: 00010286
RAX: 4141414141414141 RBX: 000000000000001b RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9903e76c100f RDI: ffff9904289d4b28
RBP: ffffbc6a40493c70 R08: 0000000093570362 R09: 0000000000000000
R10: 0000000000000000 R11: ffff9904344eae38 R12: ffff9904289d4000
R13: 0000000000000000 R14: 00000000ffffffa3 R15: ffff9903e76c100f
FS: 0000000000000000(0000) GS:ffff990434580000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007feed125a000 CR3: 00000001b860a003 CR4: 00000000003606e0
Call Trace:
process_adv_report+0x12e/0x560 [bluetooth]
hci_le_meta_evt+0x7b2/0xba0 [bluetooth]
hci_event_packet+0x1c29/0x2a90 [bluetooth]
hci_rx_work+0x19b/0x360 [bluetooth]
process_one_work+0x1eb/0x3b0
worker_thread+0x4d/0x400
kthread+0x104/0x140
Fixes:
Alain Michaud
authored and
Greg Kroah-Hartman
commited |
5df9e5613d | |
[ Upstream commit 56b5453a86203a44726f523b4133c1feca49ce7c ]
Bluetooth PTS test case HFP/AG/ACC/BI-12-I accepts SCO connection
with invalid parameter at the first SCO request expecting AG to
attempt another SCO request with the use of "safe settings" for
given codec, base on section 5.7.1.2 of HFP 1.7 specification.
This patch addresses it by adding "Invalid LMP Parameters" (0x1e)
to the SCO fallback case. Verified with below log:
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Setting: 0x0003
Input Coding: Linear
Input Data Format: 1's complement
Input Sample Size: 8-bit
# of bits padding at MSB: 0
Air Coding Format: Transparent Data
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x0380
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 256
Count: 1
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e)
Handle: 0
Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC)
Link type: eSCO (0x02)
Transmission interval: 0x00
Retransmission window: 0x02
RX packet length: 0
TX packet length: 0
Air mode: Transparent (0x03)
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 8
Setting: 0x0003
Input Coding: Linear
Input Data Format: 1's complement
Input Sample Size: 8-bit
# of bits padding at MSB: 0
Air Coding Format: Transparent Data
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x03c8
EV3 may be used
2-EV3 may not be used
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 5
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Success (0x00)
Handle: 257
Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC)
Link type: eSCO (0x02)
Transmission interval: 0x06
Retransmission window: 0x04
RX packet length: 30
TX packet length: 30
Air mode: Transparent (0x03)
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hsin-Yu Chao
authored and
Greg Kroah-Hartman
commited |
6d1ef7c11c | |
commit 71811cac8532b2387b3414f7cd8fe9e497482864 upstream. Needn't call 'rfcomm_dlc_put' here, because 'rfcomm_dlc_exists' didn't increase dlc->refcnt. Reported-by: syzbot+4496e82090657320efc6@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Suggested-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Qiujun Huang
authored and
Greg Kroah-Hartman
commited |
78a4ad2860 | |
commit 11eb85ec42dc8c7a7ec519b90ccf2eeae9409de8 upstream. Syzbot managed to trigger a use after free "KASAN: use-after-free Write in hci_sock_bind". I have reviewed the code manually and one possibly cause I have found is that we are not holding lock_sock(sk) when we do the hci_dev_put(hdev) in hci_sock_release(). My theory is that the bind and the release are racing against each other which results in this use after free. Reported-by: syzbot+eba992608adf3d796bcc@syzkaller.appspotmail.com Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Dan Carpenter
authored and
Greg Kroah-Hartman
commited |
71729b05e7 | |
commit d088337c38a5cd8f0230fbf2d514ff7672f9d0d3 upstream.
In the implementation of hci_connect_le_scan() when conn is added via
hci_conn_add(), if hci_explicit_conn_params_set() fails the allocated
memory for conn is leaked. Use hci_conn_del() to release it.
Fixes:
Navid Emamdoost
authored and
Greg Kroah-Hartman
commited |
dfde3147c6 | |
commit df66499a1fab340c167250a5743931dc50d5f0fa upstream.
We used to take a lock in amp_physical_cfm() but then we moved it to
the caller function. Unfortunately the unlock on this error path was
overlooked so it leads to a double unlock.
Fixes:
Dan Carpenter
authored and
Greg Kroah-Hartman
commited |
cf223ff1a2 | |
[ Upstream commit 6012b9346d8959194c239fd60a62dfec98d43048 ]
Instances may have flags set as part of its data in which case the code
should not attempt to add it again otherwise it can cause duplication:
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
Handle: 0x00
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x06
Flags: 0x04
BR/EDR Not Supported
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luiz Augusto von Dentz
authored and
Greg Kroah-Hartman
commited |
eef455a9b5 | |
[ Upstream commit eb8c101e28496888a0dcfe16ab86a1bee369e820 ]
During the setup() stage, HCI device drivers expect the chip to
acknowledge its setup() completion via vendor specific frames.
If userspace opens() such HCI device in HCI_USER_CHANNEL [1] mode,
the vendor specific frames are never tranmitted to the driver, as
they are filtered in hci_rx_work().
Allow HCI devices which operate in HCI_USER_CHANNEL mode to receive
frames if the HCI device is is HCI_INIT state.
[1] https://www.spinics.net/lists/linux-bluetooth/msg37345.html
Fixes:
Mattijs Korpershoek
authored and
Greg Kroah-Hartman
commited |
512de42ed7 | |
[ Upstream commit 4c371bb95cf06ded80df0e6139fdd77cee1d9a94 ]
It appears that some Broadcom controllers (eg BCM20702A0) reject LE Set
Advertising Parameters command if advertising intervals provided are not
within range for undirected and low duty directed advertising.
Workaround this bug by populating min and max intervals with 'valid'
values.
< HCI Command: LE Set Advertising Parameters (0x08|0x0006) plen 15
Min advertising interval: 0.000 msec (0x0000)
Max advertising interval: 0.000 msec (0x0000)
Type: Connectable directed - ADV_DIRECT_IND (high duty cycle) (0x01)
Own address type: Public (0x00)
Direct address type: Random (0x01)
Direct address: E2:F0:7B:9F:DC:F4 (Static)
Channel map: 37, 38, 39 (0x07)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Parameters (0x08|0x0006) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Sören Beye <linux@hypfer.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Szymon Janc
authored and
Greg Kroah-Hartman
commited |
71aaa813ba | |
[ Upstream commit 727ea61a5028f8ac96f75ab34cb1b56e63fd9227 ] It looks like in hci_init4_req() the request is being initialised from cpu-endian data but the packet is specified to be little-endian. This causes an warning from sparse due to __le16 to u16 conversion. Fix this by using cpu_to_le16() on the two fields in the packet. net/bluetooth/hci_core.c:845:27: warning: incorrect type in assignment (different base types) net/bluetooth/hci_core.c:845:27: expected restricted __le16 [usertype] tx_len net/bluetooth/hci_core.c:845:27: got unsigned short [usertype] le_max_tx_len net/bluetooth/hci_core.c:846:28: warning: incorrect type in assignment (different base types) net/bluetooth/hci_core.c:846:28: expected restricted __le16 [usertype] tx_time net/bluetooth/hci_core.c:846:28: got unsigned short [usertype] le_max_tx_time Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Ben Dooks (Codethink)
authored and
Greg Kroah-Hartman
commited |
8829e883f2 | |
[ Upstream commit a5c3021bb62b970713550db3f7fd08aa70665d7e ] If the remote is not able to fully utilize the MPS choosen recalculate the credits based on the actual amount it is sending that way it can still send packets of MTU size without credits dropping to 0. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Luiz Augusto von Dentz
authored and
Greg Kroah-Hartman
commited |
245b2765e8 | |
[ Upstream commit 3ef7cf57c72f32f61e97f8fa401bc39ea1f1a5d4 ] Many poll() handlers are lockless. Using skb_queue_empty_lockless() instead of skb_queue_empty() is more appropriate. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Eric Dumazet
authored and
Greg Kroah-Hartman
commited |
eaf548feaa | |
[ Upstream commit 68d19d7d995759b96169da5aac313363f92a9075 ] This reverts commit c49a8682fc5d298d44e8d911f4fa14690ea9485e. There are devices which require low connection intervals for usable operation including keyboards and mice. Forcing a static connection interval for these types of devices has an impact in latency and causes a regression. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Marcel Holtmann
authored and
Greg Kroah-Hartman
commited |
2af977b0d1 | |
commit 1d87b88ba26eabd4745e158ecfd87c93a9b51dc2 upstream.
Microsoft Surface Precision Mouse provides bogus identity address when
pairing. It connects with Static Random address but provides Public
Address in SMP Identity Address Information PDU. Address has same
value but type is different. Workaround this by dropping IRK if ID
address discrepancy is detected.
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 75
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: E0:52:33:93:3B:21 (Static)
Connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
....
> ACL Data RX: Handle 75 flags 0x02 dlen 12
SMP: Identity Address Information (0x09) len 7
Address type: Public (0x00)
Address: E0:52:33:93:3B:21
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Maarten Fonville <maarten.fonville@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199461
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Szymon Janc
authored and
Greg Kroah-Hartman
commited |
152ddf9f04 | |
[ Upstream commit c49a8682fc5d298d44e8d911f4fa14690ea9485e ] Problem: The Linux Bluetooth stack yields complete control over the BLE connection interval to the remote device. The Linux Bluetooth stack provides access to the BLE connection interval min and max values through /sys/kernel/debug/bluetooth/hci0/ conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval. These values are used for initial BLE connections, but the remote device has the ability to request a connection parameter update. In the event that the remote side requests to change the connection interval, the Linux kernel currently only validates that the desired value is within the acceptable range in the Bluetooth specification (6 - 3200, corresponding to 7.5ms - 4000ms). There is currently no validation that the desired value requested by the remote device is within the min/max limits specified in the conn_min_interval/conn_max_interval configurations. This essentially leads to Linux yielding complete control over the connection interval to the remote device. The proposed patch adds a verification step to the connection parameter update mechanism, ensuring that the desired value is within the min/max bounds of the current connection. If the desired value is outside of the current connection min/max values, then the connection parameter update request is rejected and the negative response is returned to the remote device. Recall that the initial connection is established using the local conn_min_interval/conn_max_interval values, so this allows the Linux administrator to retain control over the BLE connection interval. The one downside that I see is that the current default Linux values for conn_min_interval and conn_max_interval typically correspond to 30ms and 50ms respectively. If this change were accepted, then it is feasible that some devices would no longer be able to negotiate to their desired connection interval values. This might be remedied by setting the default Linux conn_min_interval and conn_max_interval values to the widest supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same behavior as the current implementation, where the remote device could request to change the connection interval value to any value that is permitted by the Bluetooth specification, and Linux would accept the desired value. Signed-off-by: Carey Sonsino <csonsino@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
csonsino
authored and
Greg Kroah-Hartman
commited |
202de90df2 | |
[ Upstream commit 28261da8a26f4915aa257d12d506c6ba179d961f ] Because of both sides doing L2CAP disconnection at the same time, it was possible to receive L2CAP Disconnection Response with CID that was already freed. That caused problems if CID was already reused and L2CAP Connection Request with same CID was sent out. Before this patch kernel deleted channel context regardless of the state of the channel. Example where leftover Disconnection Response (frame #402) causes local device to delete L2CAP channel which was not yet connected. This in turn confuses remote device's stack because same CID is re-used without properly disconnecting. Btmon capture before patch: ** snip ** > ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499 L2CAP: Disconnection Request (0x06) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548 L2CAP: Disconnection Response (0x07) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 = bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447 > HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397 L2CAP: Connection Request (0x02) ident 27 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441 L2CAP: Connection Response (0x03) ident 27 len 8 Destination CID: 65 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449 L2CAP: Configure Request (0x04) ident 19 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Similar case after the patch: *snip* > ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143 L2CAP: Disconnection Request (0x06) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073 L2CAP: Connection Request (0x02) ident 12 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371 L2CAP: Disconnection Response (0x07) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196 L2CAP: Configure Request (0x04) ident 13 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804 L2CAP: Connection Response (0x03) ident 12 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Fix is to check that channel is in state BT_DISCONN before deleting the channel. This bug was found while fuzzing Bluez's OBEX implementation using Synopsys Defensics. Reported-by: Matti Kamunen <matti.kamunen@synopsys.com> Reported-by: Ari Timonen <ari.timonen@synopsys.com> Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Matias Karhumaa
authored and
Greg Kroah-Hartman
commited |
0fdb922d0e | |
[ Upstream commit b188b03270b7f8568fc714101ce82fbf5e811c5a ] Handle overlooked case where the target address is assigned to a peer and neither route nor gateway exist. For one peer, no checks are performed to see if it is meant to receive packets for a given address. As soon as there is a second peer however, checks are performed to deal with routes and gateways for handling complex setups with multiple hops to a target address. This logic assumed that no route and no gateway imply that the destination address can not be reached, which is false in case of a direct peer. Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by: Michael Scott <mike@foundries.io> Signed-off-by: Josua Mayer <josua.mayer@jm0.eu> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
Josua Mayer
authored and
Greg Kroah-Hartman
commited |
c814f618b7 | |
commit eca94432934fe5f141d084f2e36ee2c0e614cc04 upstream.
Fix minimum encryption key size check so that HCI_MIN_ENC_KEY_SIZE is
also allowed as stated in the comment.
This bug caused connection problems with devices having maximum
encryption key size of 7 octets (56-bit).
Fixes: 693cd8ce3f88 ("Bluetooth: Fix regression with minimum encryption key size alignment")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203997
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matias Karhumaa
authored and
Greg Kroah-Hartman
commited |
5dd6139a0a | |
commit 693cd8ce3f882524a5d06f7800dd8492411877b3 upstream.
When trying to align the minimum encryption key size requirement for
Bluetooth connections, it turns out doing this in a central location in
the HCI connection handling code is not possible.
Original Bluetooth version up to 2.0 used a security model where the
L2CAP service would enforce authentication and encryption. Starting
with Bluetooth 2.1 and Secure Simple Pairing that model has changed into
that the connection initiator is responsible for providing an encrypted
ACL link before any L2CAP communication can happen.
Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and
before devices are causing a regression. The encryption key size check
needs to be moved out of the HCI connection handling into the L2CAP
channel setup.
To achieve this, the current check inside hci_conn_security() has been
moved into l2cap_check_enc_key_size() helper function and then called
from four decisions point inside L2CAP to cover all combinations of
Secure Simple Pairing enabled devices and device using legacy pairing
and legacy service security model.
Fixes: d5bb334a8e17 ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann
authored and
Greg Kroah-Hartman
commited |
db7f1076c0 | |
commit d5bb334a8e171b262e48f378bd2096c0ea458265 upstream. The minimum encryption key size for LE connections is 56 bits and to align LE with BR/EDR, enforce 56 bits of minimum encryption key size for BR/EDR connections as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann
authored and
Greg Kroah-Hartman
commited |
5e9a6c68de | |
This reverts commit
Greg Kroah-Hartman
commited |
8e5483aeae | |
[ Upstream commit f80c5dad7b6467b884c445ffea45985793b4b2d0 ]
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.
The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.
This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.
Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64) 0.352340
= Note: Bluetooth subsystem version 2.22 0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310
Address type: 0x06
LE Public
LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496
Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
João Paulo Rechi Vita
authored and
Greg Kroah-Hartman
commited |
8603d49906 | |
commit d5bb334a8e171b262e48f378bd2096c0ea458265 upstream. The minimum encryption key size for LE connections is 56 bits and to align LE with BR/EDR, enforce 56 bits of minimum encryption key size for BR/EDR connections as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann
authored and
Greg Kroah-Hartman
commited |
38f092c41c | |
commit a1616a5ac99ede5d605047a9012481ce7ff18b16 upstream. Struct ca is copied from userspace. It is not checked whether the "name" field is NULL terminated, which allows local users to obtain potentially sensitive information from kernel stack memory, via a HIDPCONNADD command. This vulnerability is similar to CVE-2011-1079. Signed-off-by: Young Xiao <YangX92@hotmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Young Xiao
authored and
Greg Kroah-Hartman
commited |
c6d1f9b4b2 | |
[ Upstream commit 30d65e0804d58a03d1a8ea4e12c6fc07ed08218b ] Fix crash caused by NULL pointer dereference when debugfs functions le_max_key_read, le_max_key_size_write, le_min_key_size_read or le_min_key_size_write and Bluetooth adapter was powered off. Fix is to move max_key_size and min_key_size from smp_dev to hci_dev. At the same time they were renamed to le_max_key_size and le_min_key_size. BUG: unable to handle kernel NULL pointer dereference at 00000000000002e8 PGD 0 P4D 0 Oops: 0000 [#24] SMP PTI CPU: 2 PID: 6255 Comm: cat Tainted: G D OE 4.18.9-200.fc28.x86_64 #1 Hardware name: LENOVO 4286CTO/4286CTO, BIOS 8DET76WW (1.46 ) 06/21/2018 RIP: 0010:le_max_key_size_read+0x45/0xb0 [bluetooth] Code: 00 00 00 48 83 ec 10 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 48 8b 87 c8 00 00 00 48 8d 7c 24 04 48 8b 80 48 0a 00 00 <48> 8b 80 e8 02 00 00 0f b6 48 52 e8 fb b6 b3 ed be 04 00 00 00 48 RSP: 0018:ffffab23c3ff3df0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 00007f0b4ca2e000 RCX: ffffab23c3ff3f08 RDX: ffffffffc0ddb033 RSI: 0000000000000004 RDI: ffffab23c3ff3df4 RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000000 R10: ffffab23c3ff3ed8 R11: 0000000000000000 R12: ffffab23c3ff3f08 R13: 00007f0b4ca2e000 R14: 0000000000020000 R15: ffffab23c3ff3f08 FS: 00007f0b4ca0f540(0000) GS:ffff91bd5e280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000002e8 CR3: 00000000629fa006 CR4: 00000000000606e0 Call Trace: full_proxy_read+0x53/0x80 __vfs_read+0x36/0x180 vfs_read+0x8a/0x140 ksys_read+0x4f/0xb0 do_syscall_64+0x5b/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Matias Karhumaa
authored and
Greg Kroah-Hartman
commited |
09b6c08061 | |
commit 7c9cbd0b5e38a1672fcd137894ace3b042dfbf69 upstream. The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len as length value. The opt->len however is in control over the remote user and can be used by an attacker to gain access beyond the bounds of the actual packet. To prevent any potential leak of heap memory, it is enough to check that the resulting len calculation after calling l2cap_get_conf_opt is not below zero. A well formed packet will always return >= 0 here and will end with the length value being zero after the last option has been parsed. In case of malformed packets messing with the opt->len field the length value will become negative. If that is the case, then just abort and ignore the option. In case an attacker uses a too short opt->len value, then garbage will be parsed, but that is protected by the unknown option handling and also the option parameter size checks. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann
authored and
Greg Kroah-Hartman
commited |
15d6538a0d | |
commit af3d5d1c87664a4f150fcf3534c6567cb19909b0 upstream. When doing option parsing for standard type values of 1, 2 or 4 octets, the value is converted directly into a variable instead of a pointer. To avoid being tricked into being a pointer, check that for these option types that sizes actually match. In L2CAP every option is fixed size and thus it is prudent anyway to ensure that the remote side sends us the right option size along with option paramters. If the option size is not matching the option type, then that option is silently ignored. It is a protocol violation and instead of trying to give the remote attacker any further hints just pretend that option is not present and proceed with the default values. Implementation following the specification and its qualification procedures will always use the correct size and thus not being impacted here. To keep the code readable and consistent accross all options, a few cosmetic changes were also required. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcel Holtmann
authored and
Greg Kroah-Hartman
commited |
2318c0e4b8 | |
commit e20a2e9c42c9e4002d9e338d74e7819e88d77162 upstream. When releasing socket, it is possible to enter hci_sock_release() and hci_sock_dev_event(HCI_DEV_UNREG) at the same time in different thread. The reference count of hdev should be decremented only once from one of them but if storing hdev to local variable in hci_sock_release() before detached from socket and setting to NULL in hci_sock_dev_event(), hci_dev_put(hdev) is unexpectedly called twice. This is resolved by referencing hdev from socket after bt_sock_unlink() in hci_sock_release(). Reported-by: syzbot+fdc00003f4efff43bc5b@syzkaller.appspotmail.com Signed-off-by: Myungho Jung <mhjungk@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Myungho Jung
authored and
Greg Kroah-Hartman
commited |
4b39051363 | |
commit c4f5627f7eeecde1bb6b646d8c0907b96dc2b2a6 upstream. With commit 
Matthias Kaehlcke
authored and
Greg Kroah-Hartman
commited |
8d368fc58e | |
commit 1629db9c75342325868243d6bca5853017d91cf8 upstream. In case a command which completes in Command Status was sent using the hci_cmd_send-family of APIs there would be a misleading error in the hci_get_cmd_complete function, since the code would be trying to fetch the Command Complete parameters when there are none. Avoid the misleading error and silently bail out from the function in case the received event is a command status. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Tested-by Adam Ford <aford173@gmail.com> #4.19.16 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Johan Hedberg
authored and
Greg Kroah-Hartman
commited |
7557895b3d | |
In case unpair_device() was called through mgmt interface at the same time when pairing was in progress, Bluetooth kernel module crash was seen. [ 600.351225] general protection fault: 0000 [#1] SMP PTI [ 600.351235] CPU: 1 PID: 11096 Comm: btmgmt Tainted: G OE 4.19.0-rc1+ #1 [ 600.351238] Hardware name: Dell Inc. Latitude E5440/08RCYC, BIOS A18 05/14/2017 [ 600.351272] RIP: 0010:smp_chan_destroy.isra.10+0xce/0x2c0 [bluetooth] [ 600.351276] Code: c0 0f 84 b4 01 00 00 80 78 28 04 0f 84 53 01 00 00 4d 85 ed 0f 85 ab 00 00 00 48 8b 08 48 8b 50 08 be 10 00 00 00 48 89 51 08 <48> 89 0a 48 b9 00 02 00 00 00 00 ad de 48 89 48 08 48 8b 83 00 01 [ 600.351279] RSP: 0018:ffffa9be839b3b50 EFLAGS: 00010246 [ 600.351282] RAX: ffff9c999ac565a0 RBX: ffff9c9996e98c00 RCX: ffff9c999aa28b60 [ 600.351285] RDX: dead000000000200 RSI: 0000000000000010 RDI: ffff9c999e403500 [ 600.351287] RBP: ffffa9be839b3b70 R08: 0000000000000000 R09: ffffffff92a25c00 [ 600.351290] R10: ffffa9be839b3ae8 R11: 0000000000000001 R12: ffff9c995375b800 [ 600.351292] R13: 0000000000000000 R14: ffff9c99619a5000 R15: ffff9c9962a01c00 [ 600.351295] FS: 00007fb2be27c700(0000) GS:ffff9c999e880000(0000) knlGS:0000000000000000 [ 600.351298] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 600.351300] CR2: 00007fb2bdadbad0 CR3: 000000041c328001 CR4: 00000000001606e0 [ 600.351302] Call Trace: [ 600.351325] smp_failure+0x4f/0x70 [bluetooth] [ 600.351345] smp_cancel_pairing+0x74/0x80 [bluetooth] [ 600.351370] unpair_device+0x1c1/0x330 [bluetooth] [ 600.351399] hci_sock_sendmsg+0x960/0x9f0 [bluetooth] [ 600.351409] ? apparmor_socket_sendmsg+0x1e/0x20 [ 600.351417] sock_sendmsg+0x3e/0x50 [ 600.351422] sock_write_iter+0x85/0xf0 [ 600.351429] do_iter_readv_writev+0x12b/0x1b0 [ 600.351434] do_iter_write+0x87/0x1a0 [ 600.351439] vfs_writev+0x98/0x110 [ 600.351443] ? ep_poll+0x16d/0x3d0 [ 600.351447] ? ep_modify+0x73/0x170 [ 600.351451] do_writev+0x61/0xf0 [ 600.351455] ? do_writev+0x61/0xf0 [ 600.351460] __x64_sys_writev+0x1c/0x20 [ 600.351465] do_syscall_64+0x5a/0x110 [ 600.351471] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 600.351474] RIP: 0033:0x7fb2bdb62fe0 [ 600.351477] Code: 73 01 c3 48 8b 0d b8 6e 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 69 c7 2c 00 00 75 10 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 de 80 01 00 48 89 04 24 [ 600.351479] RSP: 002b:00007ffe062cb8f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014 [ 600.351484] RAX: ffffffffffffffda RBX: 000000000255b3d0 RCX: 00007fb2bdb62fe0 [ 600.351487] RDX: 0000000000000001 RSI: 00007ffe062cb920 RDI: 0000000000000004 [ 600.351490] RBP: 00007ffe062cb920 R08: 000000000255bd80 R09: 0000000000000000 [ 600.351494] R10: 0000000000000353 R11: 0000000000000246 R12: 0000000000000001 [ 600.351497] R13: 00007ffe062cbbe0 R14: 0000000000000000 R15: 0000000000000000 [ 600.351501] Modules linked in: algif_hash algif_skcipher af_alg cmac ipt_MASQUERADE nf_conntrack_netlink nfnetlink xfrm_user xfrm_algo iptable_nat nf_nat_ipv4 xt_addrtype iptable_filter ip_tables xt_conntrack x_tables nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c br_netfilter bridge stp llc overlay arc4 nls_iso8859_1 dm_crypt intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp dell_laptop kvm_intel crct10dif_pclmul dell_smm_hwmon crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd cryptd glue_helper intel_cstate intel_rapl_perf uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_common videodev media hid_multitouch input_leds joydev serio_raw dell_wmi snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic dell_smbios dcdbas sparse_keymap [ 600.351569] snd_hda_intel btusb snd_hda_codec btrtl btbcm btintel snd_hda_core bluetooth(OE) snd_hwdep snd_pcm iwlmvm ecdh_generic wmi_bmof dell_wmi_descriptor snd_seq_midi mac80211 snd_seq_midi_event lpc_ich iwlwifi snd_rawmidi snd_seq snd_seq_device snd_timer cfg80211 snd soundcore mei_me mei dell_rbtn dell_smo8800 mac_hid parport_pc ppdev lp parport autofs4 hid_generic usbhid hid i915 nouveau kvmgt vfio_mdev mdev vfio_iommu_type1 vfio kvm irqbypass i2c_algo_bit ttm drm_kms_helper syscopyarea sysfillrect sysimgblt mxm_wmi psmouse ahci sdhci_pci cqhci libahci fb_sys_fops sdhci drm e1000e video wmi [ 600.351637] ---[ end trace e49e9f1df09c94fb ]--- [ 600.351664] RIP: 0010:smp_chan_destroy.isra.10+0xce/0x2c0 [bluetooth] [ 600.351666] Code: c0 0f 84 b4 01 00 00 80 78 28 04 0f 84 53 01 00 00 4d 85 ed 0f 85 ab 00 00 00 48 8b 08 48 8b 50 08 be 10 00 00 00 48 89 51 08 <48> 89 0a 48 b9 00 02 00 00 00 00 ad de 48 89 48 08 48 8b 83 00 01 [ 600.351669] RSP: 0018:ffffa9be839b3b50 EFLAGS: 00010246 [ 600.351672] RAX: ffff9c999ac565a0 RBX: ffff9c9996e98c00 RCX: ffff9c999aa28b60 [ 600.351674] RDX: dead000000000200 RSI: 0000000000000010 RDI: ffff9c999e403500 [ 600.351676] RBP: ffffa9be839b3b70 R08: 0000000000000000 R09: ffffffff92a25c00 [ 600.351679] R10: ffffa9be839b3ae8 R11: 0000000000000001 R12: ffff9c995375b800 [ 600.351681] R13: 0000000000000000 R14: ffff9c99619a5000 R15: ffff9c9962a01c00 [ 600.351684] FS: 00007fb2be27c700(0000) GS:ffff9c999e880000(0000) knlGS:0000000000000000 [ 600.351686] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 600.351689] CR2: 00007fb2bdadbad0 CR3: 000000041c328001 CR4: 00000000001606e0 Crash happened because list_del_rcu() was called twice for smp->ltk. This was possible if unpair_device was called right after ltk was generated but before keys were distributed. In this commit smp_cancel_pairing was refactored to cancel pairing if it is in progress and otherwise just removes keys. Once keys are removed from rcu list, pointers to smp context's keys are set to NULL to make sure removed list items are not accessed later. This commit also adjusts the functionality of mgmt unpair_device() little bit. Previously pairing was canceled only if pairing was in state that keys were already generated. With this commit unpair_device() cancels pairing already in earlier states. Bug was found by fuzzing kernel SMP implementation using Synopsys Defensics. Reported-by: Pekka Oikarainen <pekka.oikarainen@synopsys.com> Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Matias Karhumaa
authored and
Johan Hedberg
commited |
cb28c306b9 | |
In case local OOB data was generated and other device initiated pairing
claiming that it has got OOB data, following crash occurred:
[ 222.847853] general protection fault: 0000 [#1] SMP PTI
[ 222.848025] CPU: 1 PID: 42 Comm: kworker/u5:0 Tainted: G C 4.18.0-custom #4
[ 222.848158] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 222.848307] Workqueue: hci0 hci_rx_work [bluetooth]
[ 222.848416] RIP: 0010:compute_ecdh_secret+0x5a/0x270 [bluetooth]
[ 222.848540] Code: 0c af f5 48 8b 3d 46 de f0 f6 ba 40 00 00 00 be c0 00 60 00 e8 b7 7b c5 f5 48 85 c0 0f 84 ea 01 00 00 48 89 c3 e8 16 0c af f5 <49> 8b 47 38 be c0 00 60 00 8b 78 f8 48 83 c7 48 e8 51 84 c5 f5 48
[ 222.848914] RSP: 0018:ffffb1664087fbc0 EFLAGS: 00010293
[ 222.849021] RAX: ffff8a5750d7dc00 RBX: ffff8a5671096780 RCX: ffffffffc08bc32a
[ 222.849111] RDX: 0000000000000000 RSI: 00000000006000c0 RDI: ffff8a5752003800
[ 222.849192] RBP: ffffb1664087fc60 R08: ffff8a57525280a0 R09: ffff8a5752003800
[ 222.849269] R10: ffffb1664087fc70 R11: 0000000000000093 R12: ffff8a5674396e00
[ 222.849350] R13: ffff8a574c2e79aa R14: ffff8a574c2e796a R15: 020e0e100d010101
[ 222.849429] FS: 0000000000000000(0000) GS:ffff8a5752500000(0000) knlGS:0000000000000000
[ 222.849518] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 222.849586] CR2: 000055856016a038 CR3: 0000000110d2c005 CR4: 00000000000606e0
[ 222.849671] Call Trace:
[ 222.849745] ? sc_send_public_key+0x110/0x2a0 [bluetooth]
[ 222.849825] ? sc_send_public_key+0x115/0x2a0 [bluetooth]
[ 222.849925] smp_recv_cb+0x959/0x2490 [bluetooth]
[ 222.850023] ? _cond_resched+0x19/0x40
[ 222.850105] ? mutex_lock+0x12/0x40
[ 222.850202] l2cap_recv_frame+0x109d/0x3420 [bluetooth]
[ 222.850315] ? l2cap_recv_frame+0x109d/0x3420 [bluetooth]
[ 222.850426] ? __switch_to_asm+0x34/0x70
[ 222.850515] ? __switch_to_asm+0x40/0x70
[ 222.850625] ? __switch_to_asm+0x34/0x70
[ 222.850724] ? __switch_to_asm+0x40/0x70
[ 222.850786] ? __switch_to_asm+0x34/0x70
[ 222.850846] ? __switch_to_asm+0x40/0x70
[ 222.852581] ? __switch_to_asm+0x34/0x70
[ 222.854976] ? __switch_to_asm+0x40/0x70
[ 222.857475] ? __switch_to_asm+0x40/0x70
[ 222.859775] ? __switch_to_asm+0x34/0x70
[ 222.861218] ? __switch_to_asm+0x40/0x70
[ 222.862327] ? __switch_to_asm+0x34/0x70
[ 222.863758] l2cap_recv_acldata+0x266/0x3c0 [bluetooth]
[ 222.865122] hci_rx_work+0x1c9/0x430 [bluetooth]
[ 222.867144] process_one_work+0x210/0x4c0
[ 222.868248] worker_thread+0x41/0x4d0
[ 222.869420] kthread+0x141/0x160
[ 222.870694] ? process_one_work+0x4c0/0x4c0
[ 222.871668] ? kthread_create_worker_on_cpu+0x90/0x90
[ 222.872896] ret_from_fork+0x35/0x40
[ 222.874132] Modules linked in: algif_hash algif_skcipher af_alg rfcomm bnep btusb btrtl btbcm btintel snd_intel8x0 cmac intel_rapl_perf vboxvideo(C) snd_ac97_codec bluetooth ac97_bus joydev ttm snd_pcm ecdh_generic drm_kms_helper snd_timer snd input_leds drm serio_raw fb_sys_fops soundcore syscopyarea sysfillrect sysimgblt mac_hid sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear hid_generic usbhid hid crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd cryptd glue_helper ahci psmouse libahci i2c_piix4 video e1000 pata_acpi
[ 222.883153] fbcon_switch: detected unhandled fb_set_par error, error code -16
[ 222.886774] fbcon_switch: detected unhandled fb_set_par error, error code -16
[ 222.890503] ---[ end trace 6504aa7a777b5316 ]---
[ 222.890541] RIP: 0010:compute_ecdh_secret+0x5a/0x270 [bluetooth]
[ 222.890551] Code: 0c af f5 48 8b 3d 46 de f0 f6 ba 40 00 00 00 be c0 00 60 00 e8 b7 7b c5 f5 48 85 c0 0f 84 ea 01 00 00 48 89 c3 e8 16 0c af f5 <49> 8b 47 38 be c0 00 60 00 8b 78 f8 48 83 c7 48 e8 51 84 c5 f5 48
[ 222.890555] RSP: 0018:ffffb1664087fbc0 EFLAGS: 00010293
[ 222.890561] RAX: ffff8a5750d7dc00 RBX: ffff8a5671096780 RCX: ffffffffc08bc32a
[ 222.890565] RDX: 0000000000000000 RSI: 00000000006000c0 RDI: ffff8a5752003800
[ 222.890571] RBP: ffffb1664087fc60 R08: ffff8a57525280a0 R09: ffff8a5752003800
[ 222.890576] R10: ffffb1664087fc70 R11: 0000000000000093 R12: ffff8a5674396e00
[ 222.890581] R13: ffff8a574c2e79aa R14: ffff8a574c2e796a R15: 020e0e100d010101
[ 222.890586] FS: 0000000000000000(0000) GS:ffff8a5752500000(0000) knlGS:0000000000000000
[ 222.890591] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 222.890594] CR2: 000055856016a038 CR3: 0000000110d2c005 CR4: 00000000000606e0
This commit fixes a bug where invalid pointer to crypto tfm was used for
SMP SC ECDH calculation when OOB was in use. Solution is to use same
crypto tfm than when generating OOB material on generate_oob() function.
This bug was introduced in commit
Matias Karhumaa
authored and
Marcel Holtmann
commited |
4ba5175f2c | |
A remote device may claim that it has received our OOB data, even though we never geneated it. Add a new flag to track whether we actually have OOB data, and ignore the remote peer's flag if haven't generated OOB data. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg
authored and
Marcel Holtmann
commited |
94f14e4728 | |
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
Linus Torvalds
commited |
9a76aba02a | |
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
NfoE
=lNwq
-----END PGP SIGNATURE-----
Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED triggers improvements make the biggest part of this pull request.
The most striking ones, that allowed for nice cleanups in the triggers
are:
- centralized handling of creation and removal of trigger sysfs
attributes via attribute group
- addition of module_led_trigger() helper
The other things that need to be mentioned:
New features and improvements to existing LED class drivers:
- lt3593: add DT support, switch to gpiod interface
- lm3692x: support LED sync configuration, change OF calls to fwnode
calls
- apu: modify PC Engines apu/apu2 driver to support apu3
Change in the drivers/net/can/led.c:
- mark led trigger as broken since it's in the way for the further
cleanups. It implements a subset of the netdev trigger and an Ack
is needed from someone who can actually test and confirm that the
netdev trigger works for can devices"
* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
leds: ns2: Change unsigned to unsigned int
usb: simplify usbport trigger
leds: gpio trigger: simplifications from core changes
leds: backlight trigger: simplifications from core changes
leds: activity trigger: simplifications from core changes
leds: default-on trigger: make use of module_led_trigger()
leds: heartbeat trigger: simplifications from core changes
leds: oneshot trigger: simplifications from core changes
leds: transient trigger: simplifications from core changes
leds: timer trigger: simplifications from core changes
leds: netdev trigger: simplifications from core changes
leds: triggers: new function led_set_trigger_data()
leds: triggers: define module_led_trigger helper
leds: triggers: handle .trigger_data and .activated() in the core
leds: triggers: add device attribute support
leds: triggers: let struct led_trigger::activate() return an error code
leds: triggers: make the MODULE_LICENSE string match the actual license
leds: lm3692x: Support LED sync configuration
dt: bindings: lm3692x: Update binding for LED sync control
leds: lm3692x: Change DT calls to fwnode calls
...
Linus Torvalds
commited |
c07b3682cd |