ARM: SoC driver updates for v4.5

Driver updates for ARM SoCs. Some for SoC-family code under drivers/soc,
 but also some other driver updates that don't belong anywhere else. We also
 bring in the drivers/reset code through arm-soc.
 
 Some of the larger updates:
 
 - Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate with other
   parts of the chip/board on these platforms, all proprietary protocols that
   don't fit into other subsystems and live in drivers/soc for now.
 
 - System bus driver for UniPhier
 - Driver for the TI Wakeup M3 IPC device
 
 - Power management for Raspberry PI
 
 + Again a bunch of other smaller updates and patches.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWnsLfAAoJEIwa5zzehBx3KVcQAJS90XyeheS3LX+SUMsn5qAJ
 Q+NLzfYAAHZPafruOTcBATs9xUvuJM4KsdqXIWiA4gJig/ZFpF5dpDbrnhpdJFEK
 0ULSfZd9J4B4m7aBo6L8lVBEbd4i++updHpIYnmPx3tkLL0Win/VM8KlMpdOzMQN
 DncNFVIRJ80OxepdHgBu6yY7gv3Z8XhRrNukeG8EZTvHw5bJQHfjMOeAQNQWUmWa
 HLyO6uqYkca38XMJOhPhqt0mOpwh/X6ByUueIrIMpOksJcRnklrkjDnBuvp9dQ+8
 fU1sOjjYzQPiA6Oa3o/2ruBKj2FymLJ0OzONJb3xPiBO5bJbc1LJwK00tuIRC3hv
 r9Jqoqwae/AolqYephfao/LvUcoyHBaZ6aSbGQYms0Wy2FCkkkocfY2i7QP6S6Mz
 qtOCHxX+yF921AEZ1xTOKgBvBU931WM1MQOe4s1QVllRlLFJhrGqDDwsNlPwRa+6
 OkXmPJSEhsHGFaCdA3iOEy+/W2dvMbVOaGa9csNDpPcSJhhpxc5A4CYRlFSwGyM1
 oL20g1T3ybDP+EkNcdpavWdQ55toWGmm48PunIZImVSdgNRZZQJw107yA/UzQTNz
 kOg27kqtjpM4xcpxmwGlIj4Zoy1M390ACm+n79Awa9agvjOvfV4QE1tLB4tiXyuy
 0Pxy8WWL/G5Si8bKWsfc
 =khZ5
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.  Some for SoC-family code under
  drivers/soc, but also some other driver updates that don't belong
  anywhere else.  We also bring in the drivers/reset code through
  arm-soc.

  Some of the larger updates:

   - Qualcomm support for SMEM, SMSM, SMP2P.  All used to communicate
     with other parts of the chip/board on these platforms, all
     proprietary protocols that don't fit into other subsystems and live
     in drivers/soc for now.

   - System bus driver for UniPhier

   - Driver for the TI Wakeup M3 IPC device

   - Power management for Raspberry PI

  + Again a bunch of other smaller updates and patches"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  bus: uniphier: allow only built-in driver
  ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
  MAINTAINERS: Drop Kumar Gala from QCOM
  bus: uniphier-system-bus: add UniPhier System Bus driver
  ARM: bcm2835: add rpi power domain driver
  dt-bindings: add rpi power domain driver bindings
  ARM: bcm2835: Define two new packets from the latest firmware.
  drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
  soc: mediatek: SCPSYS: Add regulator support
  MAINTAINERS: Change QCOM entries
  soc: qcom: smd-rpm: Add existing platform support
  memory/tegra: Add number of TLB lines for Tegra124
  reset: hi6220: fix modular build
  soc: qcom: Introduce WCNSS_CTRL SMD client
  ARM: qcom: select ARM_CPU_SUSPEND for power management
  MAINTAINERS: Add rules for Qualcomm dts files
  soc: qcom: enable smsm/smp2p modular build
  serial: msm_serial: Make config tristate
  soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
  soc: qcom: smsm: Add driver for Qualcomm SMSM
  ...

Documentation/devicetree/bindings/bus/uniphier-system-bus.txt

@@ -0,0 +1,66 @@
+UniPhier System Bus
+
+The UniPhier System Bus is an external bus that connects on-board devices to
+the UniPhier SoC.  It is a simple (semi-)parallel bus with address, data, and
+some control signals.  It supports up to 8 banks (chip selects).
+
+Before any access to the bus, the bus controller must be configured; the bus
+controller registers provide the control for the translation from the offset
+within each bank to the CPU-viewed address.  The needed setup includes the base
+address, the size of each bank.  Optionally, some timing parameters can be
+optimized for faster bus access.
+
+Required properties:
+- compatible: should be "socionext,uniphier-system-bus".
+- reg: offset and length of the register set for the bus controller device.
+- #address-cells: should be 2.  The first cell is the bank number (chip select).
+  The second cell is the address offset within the bank.
+- #size-cells: should be 1.
+- ranges: should provide a proper address translation from the System Bus to
+  the parent bus.
+
+Note:
+The address region(s) that can be assigned for the System Bus is implementation
+defined.  Some SoCs can use 0x00000000-0x0fffffff and 0x40000000-0x4fffffff,
+while other SoCs can only use 0x40000000-0x4fffffff.  There might be additional
+limitations depending on SoCs and the boot mode.  The address translation is
+arbitrary as long as the banks are assigned in the supported address space with
+the required alignment and they do not overlap one another.
+For example, it is possible to map:
+  bank 0 to 0x42000000-0x43ffffff, bank 5 to 0x46000000-0x46ffffff
+It is also possible to map:
+  bank 0 to 0x48000000-0x49ffffff, bank 5 to 0x44000000-0x44ffffff
+There is no reason to stick to a particular translation mapping, but the
+"ranges" property should provide a "reasonable" default that is known to work.
+The software should initialize the bus controller according to it.
+
+Example:
+
+	system-bus {
+		compatible = "socionext,uniphier-system-bus";
+		reg = <0x58c00000 0x400>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0x00000000 0x42000000 0x02000000
+			  5 0x00000000 0x46000000 0x01000000>;
+
+		ethernet@1,01f00000 {
+			compatible = "smsc,lan9115";
+			reg = <1 0x01f00000 0x1000>;
+			interrupts = <0 48 4>
+			phy-mode = "mii";
+		};
+
+		uart@5,00200000 {
+			compatible = "ns16550a";
+			reg = <5 0x00200000 0x20>;
+			interrupts = <0 49 4>
+			clock-frequency = <12288000>;
+		};
+	};
+
+In this example,
+ - the Ethernet device is connected at the offset 0x01f00000 of CS1 and
+   mapped to 0x43f00000 of the parent bus.
+ - the UART device is connected at the offset 0x00200000 of CS5 and
+   mapped to 0x46200000 of the parent bus.

Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt

@@ -0,0 +1,34 @@
+Hisilicon System Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+The reset controller registers are part of the system-ctl block on
+hi6220 SoC.
+
+Required properties:
+- compatible: may be "hisilicon,hi6220-sysctrl"
+- reg: should be register base and length as documented in the
+  datasheet
+- #reset-cells: 1, see below
+
+Example:
+sys_ctrl: sys_ctrl@f7030000 {
+	compatible = "hisilicon,hi6220-sysctrl", "syscon";
+	reg = <0x0 0xf7030000 0x0 0x2000>;
+	#clock-cells = <1>;
+	#reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+example:
+
+        uart1: serial@..... {
+                ...
+                resets = <&sys_ctrl PERIPH_RSTEN3_UART1>;
+                ...
+        };
+
+The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>.

Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt

@@ -0,0 +1,47 @@
+Raspberry Pi power domain driver
+
+Required properties:
+
+- compatible:		Should be "raspberrypi,bcm2835-power".
+- firmware:		Reference to the RPi firmware device node.
+- #power-domain-cells:	Should be <1>, we providing multiple power domains.
+
+The valid defines for power domain are:
+
+ RPI_POWER_DOMAIN_I2C0
+ RPI_POWER_DOMAIN_I2C1
+ RPI_POWER_DOMAIN_I2C2
+ RPI_POWER_DOMAIN_VIDEO_SCALER
+ RPI_POWER_DOMAIN_VPU1
+ RPI_POWER_DOMAIN_HDMI
+ RPI_POWER_DOMAIN_USB
+ RPI_POWER_DOMAIN_VEC
+ RPI_POWER_DOMAIN_JPEG
+ RPI_POWER_DOMAIN_H264
+ RPI_POWER_DOMAIN_V3D
+ RPI_POWER_DOMAIN_ISP
+ RPI_POWER_DOMAIN_UNICAM0
+ RPI_POWER_DOMAIN_UNICAM1
+ RPI_POWER_DOMAIN_CCP2RX
+ RPI_POWER_DOMAIN_CSI2
+ RPI_POWER_DOMAIN_CPI
+ RPI_POWER_DOMAIN_DSI0
+ RPI_POWER_DOMAIN_DSI1
+ RPI_POWER_DOMAIN_TRANSPOSER
+ RPI_POWER_DOMAIN_CCP2TX
+ RPI_POWER_DOMAIN_CDP
+ RPI_POWER_DOMAIN_ARM
+
+Example:
+
+power: power {
+	compatible = "raspberrypi,bcm2835-power";
+	firmware = <&firmware>;
+	#power-domain-cells = <1>;
+};
+
+Example for using power domain:
+
+&usb {
+       power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};

Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt

@@ -0,0 +1,57 @@
+Wakeup M3 IPC Driver
+=====================
+
+The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor
+(commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
+that cannot be controlled from the MPU, like suspend/resume and certain deep
+C-states for CPU Idle. Once the wkup_m3_ipc driver uses the wkup_m3_rproc driver
+to boot the wkup_m3, it handles communication with the CM3 using IPC registers
+present in the SoC's control module and a mailbox. The wkup_m3_ipc exposes an
+API to allow the SoC PM code to execute specific PM tasks.
+
+Wkup M3 Device Node:
+====================
+A wkup_m3_ipc device node is used to represent the IPC registers within an
+SoC.
+
+Required properties:
+--------------------
+- compatible:		Should be,
+				"ti,am3352-wkup-m3-ipc" for AM33xx SoCs
+				"ti,am4372-wkup-m3-ipc" for AM43xx SoCs
+- reg:			Contains the IPC register address space to communicate
+			with the Wakeup M3 processor
+- interrupts:		Contains the interrupt information for the wkup_m3
+			interrupt that signals the MPU.
+- ti,rproc:		phandle to the wkup_m3 rproc node so the IPC driver
+			can boot it.
+- mboxes:		phandles used by IPC framework to get correct mbox
+			channel for communication. Must point to appropriate
+			mbox_wkupm3 child node.
+
+Example:
+--------
+/* AM33xx */
+	l4_wkup: l4_wkup@44c00000 {
+		...
+
+		scm: scm@210000 {
+			compatible = "ti,am3-scm", "simple-bus";
+			reg = <0x210000 0x2000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x210000 0x2000>;
+
+			...
+
+			wkup_m3_ipc: wkup_m3_ipc@1324 {
+				compatible = "ti,am3352-wkup-m3-ipc";
+				reg = <0x1324 0x24>;
+				interrupts = <78>;
+				ti,rproc = <&wkup_m3>;
+				mboxes = <&mailbox &mbox_wkupm3>;
+			};
+
+			...
+		};
+	};

MAINTAINERS

@@ -1415,12 +1415,13 @@ W:	http://www.arm.linux.org.uk/
 S:	Maintained
 
 ARM/QUALCOMM SUPPORT
-M:	Kumar Gala <galak@codeaurora.org>
-M:	Andy Gross <agross@codeaurora.org>
-M:	David Brown <davidb@codeaurora.org>
+M:	Andy Gross <andy.gross@linaro.org>
+M:	David Brown <david.brown@linaro.org>
 L:	linux-arm-msm@vger.kernel.org
 L:	linux-soc@vger.kernel.org
 S:	Maintained
+F:	arch/arm/boot/dts/qcom-*.dts
+F:	arch/arm/boot/dts/qcom-*.dtsi
 F:	arch/arm/mach-qcom/
 F:	drivers/soc/qcom/
 F:	drivers/tty/serial/msm_serial.h
@@ -1428,7 +1429,7 @@ F:	drivers/tty/serial/msm_serial.c
 F:	drivers/*/pm8???-*
 F:	drivers/mfd/ssbi.c
 F:	drivers/firmware/qcom_scm.c
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux.git
 
 ARM/RADISYS ENP2611 MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -1673,6 +1674,7 @@ F:	arch/arm/include/asm/hardware/cache-uniphier.h
 F:	arch/arm/mach-uniphier/
 F:	arch/arm/mm/cache-uniphier.c
 F:	arch/arm64/boot/dts/socionext/
+F:	drivers/bus/uniphier-system-bus.c
 F:	drivers/i2c/busses/i2c-uniphier*
 F:	drivers/pinctrl/uniphier/
 F:	drivers/tty/serial/8250/8250_uniphier.c

arch/arm64/boot/dts/hisilicon/hi6220.dtsi

@@ -147,6 +147,7 @@
 			compatible = "hisilicon,hi6220-sysctrl", "syscon";
 			reg = <0x0 0xf7030000 0x0 0x2000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		media_ctrl: media_ctrl@f4410000 {

drivers/bus/Kconfig

@@ -131,6 +131,14 @@ config SUNXI_RSB
 	  with various RSB based devices, such as AXP223, AXP8XX PMICs,
 	  and AC100/AC200 ICs.
 
+config UNIPHIER_SYSTEM_BUS
+	bool "UniPhier System Bus driver"
+	depends on ARCH_UNIPHIER && OF
+	default y
+	help
+	  Support for UniPhier System Bus, a simple external bus.  This is
+	  needed to use on-board devices connected to UniPhier SoCs.
+
 config VEXPRESS_CONFIG
 	bool "Versatile Express configuration bus"
 	default y if ARCH_VEXPRESS

drivers/bus/Makefile

@@ -17,4 +17,5 @@ obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_SIMPLE_PM_BUS)	+= simple-pm-bus.o
+obj-$(CONFIG_UNIPHIER_SYSTEM_BUS)	+= uniphier-system-bus.o
 obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o

drivers/bus/uniphier-system-bus.c

@@ -0,0 +1,281 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/log2.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+/* System Bus Controller registers */
+#define UNIPHIER_SBC_BASE	0x100	/* base address of bank0 space */
+#define    UNIPHIER_SBC_BASE_BE		BIT(0)	/* bank_enable */
+#define UNIPHIER_SBC_CTRL0	0x200	/* timing parameter 0 of bank0 */
+#define UNIPHIER_SBC_CTRL1	0x204	/* timing parameter 1 of bank0 */
+#define UNIPHIER_SBC_CTRL2	0x208	/* timing parameter 2 of bank0 */
+#define UNIPHIER_SBC_CTRL3	0x20c	/* timing parameter 3 of bank0 */
+#define UNIPHIER_SBC_CTRL4	0x300	/* timing parameter 4 of bank0 */
+
+#define UNIPHIER_SBC_STRIDE	0x10	/* register stride to next bank */
+#define UNIPHIER_SBC_NR_BANKS	8	/* number of banks (chip select) */
+#define UNIPHIER_SBC_BASE_DUMMY	0xffffffff	/* data to squash bank 0, 1 */
+
+struct uniphier_system_bus_bank {
+	u32 base;
+	u32 end;
+};
+
+struct uniphier_system_bus_priv {
+	struct device *dev;
+	void __iomem *membase;
+	struct uniphier_system_bus_bank bank[UNIPHIER_SBC_NR_BANKS];
+};
+
+static int uniphier_system_bus_add_bank(struct uniphier_system_bus_priv *priv,
+					int bank, u32 addr, u64 paddr, u32 size)
+{
+	u64 end, mask;
+
+	dev_dbg(priv->dev,
+		"range found: bank = %d, addr = %08x, paddr = %08llx, size = %08x\n",
+		bank, addr, paddr, size);
+
+	if (bank >= ARRAY_SIZE(priv->bank)) {
+		dev_err(priv->dev, "unsupported bank number %d\n", bank);
+		return -EINVAL;
+	}
+
+	if (priv->bank[bank].base || priv->bank[bank].end) {
+		dev_err(priv->dev,
+			"range for bank %d has already been specified\n", bank);
+		return -EINVAL;
+	}
+
+	if (paddr > U32_MAX) {
+		dev_err(priv->dev, "base address %llx is too high\n", paddr);
+		return -EINVAL;
+	}
+
+	end = paddr + size;
+
+	if (addr > paddr) {
+		dev_err(priv->dev,
+			"base %08x cannot be mapped to %08llx of parent\n",
+			addr, paddr);
+		return -EINVAL;
+	}
+	paddr -= addr;
+
+	paddr = round_down(paddr, 0x00020000);
+	end = round_up(end, 0x00020000);
+
+	if (end > U32_MAX) {
+		dev_err(priv->dev, "end address %08llx is too high\n", end);
+		return -EINVAL;
+	}
+	mask = paddr ^ (end - 1);
+	mask = roundup_pow_of_two(mask);
+
+	paddr = round_down(paddr, mask);
+	end = round_up(end, mask);
+
+	priv->bank[bank].base = paddr;
+	priv->bank[bank].end = end;
+
+	dev_dbg(priv->dev, "range added: bank = %d, addr = %08x, end = %08x\n",
+		bank, priv->bank[bank].base, priv->bank[bank].end);
+
+	return 0;
+}
+
+static int uniphier_system_bus_check_overlap(
+				const struct uniphier_system_bus_priv *priv)
+{
+	int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
+		for (j = i + 1; j < ARRAY_SIZE(priv->bank); j++) {
+			if (priv->bank[i].end > priv->bank[j].base ||
+			    priv->bank[i].base < priv->bank[j].end) {
+				dev_err(priv->dev,
+					"region overlap between bank%d and bank%d\n",
+					i, j);
+				return -EINVAL;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static void uniphier_system_bus_check_boot_swap(
+					struct uniphier_system_bus_priv *priv)
+{
+	void __iomem *base_reg = priv->membase + UNIPHIER_SBC_BASE;
+	int is_swapped;
+
+	is_swapped = !(readl(base_reg) & UNIPHIER_SBC_BASE_BE);
+
+	dev_dbg(priv->dev, "Boot Swap: %s\n", is_swapped ? "on" : "off");
+
+	/*
+	 * If BOOT_SWAP was asserted on power-on-reset, the CS0 and CS1 are
+	 * swapped.  In this case, bank0 and bank1 should be swapped as well.
+	 */
+	if (is_swapped)
+		swap(priv->bank[0], priv->bank[1]);
+}
+
+static void uniphier_system_bus_set_reg(
+				const struct uniphier_system_bus_priv *priv)
+{
+	void __iomem *base_reg = priv->membase + UNIPHIER_SBC_BASE;
+	u32 base, end, mask, val;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
+		base = priv->bank[i].base;
+		end = priv->bank[i].end;
+
+		if (base == end) {
+			/*
+			 * If SBC_BASE0 or SBC_BASE1 is set to zero, the access
+			 * to anywhere in the system bus space is routed to
+			 * bank 0 (if boot swap if off) or bank 1 (if boot swap
+			 * if on).  It means that CPUs cannot get access to
+			 * bank 2 or later.  In other words, bank 0/1 cannot
+			 * be disabled even if its bank_enable bits is cleared.
+			 * This seems odd, but it is how this hardware goes.
+			 * As a workaround, dummy data (0xffffffff) should be
+			 * set when the bank 0/1 is unused.  As for bank 2 and
+			 * later, they can be simply disable by clearing the
+			 * bank_enable bit.
+			 */
+			if (i < 2)
+				val = UNIPHIER_SBC_BASE_DUMMY;
+			else
+				val = 0;
+		} else {
+			mask = base ^ (end - 1);
+
+			val = base & 0xfffe0000;
+			val |= (~mask >> 16) & 0xfffe;
+			val |= UNIPHIER_SBC_BASE_BE;
+		}
+		dev_dbg(priv->dev, "SBC_BASE[%d] = 0x%08x\n", i, val);
+
+		writel(val, base_reg + UNIPHIER_SBC_STRIDE * i);
+	}
+}
+
+static int uniphier_system_bus_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct uniphier_system_bus_priv *priv;
+	struct resource *regs;
+	const __be32 *ranges;
+	u32 cells, addr, size;
+	u64 paddr;
+	int pna, bank, rlen, rone, ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->membase = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(priv->membase))
+		return PTR_ERR(priv->membase);
+
+	priv->dev = dev;
+
+	pna = of_n_addr_cells(dev->of_node);
+
+	ret = of_property_read_u32(dev->of_node, "#address-cells", &cells);
+	if (ret) {
+		dev_err(dev, "failed to get #address-cells\n");
+		return ret;
+	}
+	if (cells != 2) {
+		dev_err(dev, "#address-cells must be 2\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(dev->of_node, "#size-cells", &cells);
+	if (ret) {
+		dev_err(dev, "failed to get #size-cells\n");
+		return ret;
+	}
+	if (cells != 1) {
+		dev_err(dev, "#size-cells must be 1\n");
+		return -EINVAL;
+	}
+
+	ranges = of_get_property(dev->of_node, "ranges", &rlen);
+	if (!ranges) {
+		dev_err(dev, "failed to get ranges property\n");
+		return -ENOENT;
+	}
+
+	rlen /= sizeof(*ranges);
+	rone = pna + 2;
+
+	for (; rlen >= rone; rlen -= rone) {
+		bank = be32_to_cpup(ranges++);
+		addr = be32_to_cpup(ranges++);
+		paddr = of_translate_address(dev->of_node, ranges);
+		if (paddr == OF_BAD_ADDR)
+			return -EINVAL;
+		ranges += pna;
+		size = be32_to_cpup(ranges++);
+
+		ret = uniphier_system_bus_add_bank(priv, bank, addr,
+						   paddr, size);
+		if (ret)
+			return ret;
+	}
+
+	ret = uniphier_system_bus_check_overlap(priv);
+	if (ret)
+		return ret;
+
+	uniphier_system_bus_check_boot_swap(priv);
+
+	uniphier_system_bus_set_reg(priv);
+
+	/* Now, the bus is configured.  Populate platform_devices below it */
+	return of_platform_populate(dev->of_node, of_default_bus_match_table,
+				    NULL, dev);
+}
+
+static const struct of_device_id uniphier_system_bus_match[] = {
+	{ .compatible = "socionext,uniphier-system-bus" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_system_bus_match);
+
+static struct platform_driver uniphier_system_bus_driver = {
+	.probe		= uniphier_system_bus_probe,
+	.driver = {
+		.name	= "uniphier-system-bus",
+		.of_match_table = uniphier_system_bus_match,
+	},
+};
+module_platform_driver(uniphier_system_bus_driver);
+
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_DESCRIPTION("UniPhier System Bus driver");
+MODULE_LICENSE("GPL");

drivers/memory/tegra/tegra124.c

@@ -1007,6 +1007,7 @@ static const struct tegra_smmu_soc tegra124_smmu_soc = {
 	.num_swgroups = ARRAY_SIZE(tegra124_swgroups),
 	.supports_round_robin_arbitration = true,
 	.supports_request_limit = true,
+	.num_tlb_lines = 32,
 	.num_asids = 128,
 };
 

drivers/reset/Kconfig

@@ -13,3 +13,4 @@ menuconfig RESET_CONTROLLER
 	  If unsure, say no.
 
 source "drivers/reset/sti/Kconfig"
+source "drivers/reset/hisilicon/Kconfig"

drivers/reset/Makefile

@@ -1,8 +1,9 @@
-obj-$(CONFIG_RESET_CONTROLLER) += core.o
+obj-y += core.o
 obj-$(CONFIG_ARCH_LPC18XX) += reset-lpc18xx.o
 obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
 obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
 obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
 obj-$(CONFIG_ARCH_STI) += sti/
+obj-$(CONFIG_ARCH_HISI) += hisilicon/
 obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
 obj-$(CONFIG_ATH79) += reset-ath79.o

drivers/reset/core.c

@@ -30,7 +30,6 @@ static LIST_HEAD(reset_controller_list);
  */
 struct reset_control {
 	struct reset_controller_dev *rcdev;
-	struct device *dev;
 	unsigned int id;
 };
 
@@ -95,7 +94,7 @@ int reset_control_reset(struct reset_control *rstc)
 	if (rstc->rcdev->ops->reset)
 		return rstc->rcdev->ops->reset(rstc->rcdev, rstc->id);
 
-	return -ENOSYS;
+	return -ENOTSUPP;
 }
 EXPORT_SYMBOL_GPL(reset_control_reset);
 
@@ -108,7 +107,7 @@ int reset_control_assert(struct reset_control *rstc)
 	if (rstc->rcdev->ops->assert)
 		return rstc->rcdev->ops->assert(rstc->rcdev, rstc->id);
 
-	return -ENOSYS;
+	return -ENOTSUPP;
 }
 EXPORT_SYMBOL_GPL(reset_control_assert);
 
@@ -121,7 +120,7 @@ int reset_control_deassert(struct reset_control *rstc)
 	if (rstc->rcdev->ops->deassert)
 		return rstc->rcdev->ops->deassert(rstc->rcdev, rstc->id);
 
-	return -ENOSYS;
+	return -ENOTSUPP;
 }
 EXPORT_SYMBOL_GPL(reset_control_deassert);
 
@@ -136,32 +135,29 @@ int reset_control_status(struct reset_control *rstc)
 	if (rstc->rcdev->ops->status)
 		return rstc->rcdev->ops->status(rstc->rcdev, rstc->id);
 
-	return -ENOSYS;
+	return -ENOTSUPP;
 }
 EXPORT_SYMBOL_GPL(reset_control_status);
 
 /**
- * of_reset_control_get - Lookup and obtain a reference to a reset controller.
+ * of_reset_control_get_by_index - Lookup and obtain a reference to a reset
+ * controller by index.
  * @node: device to be reset by the controller
- * @id: reset line name
+ * @index: index of the reset controller
  *
- * Returns a struct reset_control or IS_ERR() condition containing errno.
- *
- * Use of id names is optional.
+ * This is to be used to perform a list of resets for a device or power domain
+ * in whatever order. Returns a struct reset_control or IS_ERR() condition
+ * containing errno.
  */
-struct reset_control *of_reset_control_get(struct device_node *node,
-					   const char *id)
+struct reset_control *of_reset_control_get_by_index(struct device_node *node,
+					   int index)
 {
 	struct reset_control *rstc = ERR_PTR(-EPROBE_DEFER);
 	struct reset_controller_dev *r, *rcdev;
 	struct of_phandle_args args;
-	int index = 0;
 	int rstc_id;
 	int ret;
 
-	if (id)
-		index = of_property_match_string(node,
-						 "reset-names", id);
 	ret = of_parse_phandle_with_args(node, "resets", "#reset-cells",
 					 index, &args);
 	if (ret)
@@ -202,6 +198,30 @@ struct reset_control *of_reset_control_get(struct device_node *node,
 
 	return rstc;
 }
+EXPORT_SYMBOL_GPL(of_reset_control_get_by_index);
+
+/**
+ * of_reset_control_get - Lookup and obtain a reference to a reset controller.
+ * @node: device to be reset by the controller
+ * @id: reset line name
+ *
+ * Returns a struct reset_control or IS_ERR() condition containing errno.
+ *
+ * Use of id names is optional.
+ */
+struct reset_control *of_reset_control_get(struct device_node *node,
+					   const char *id)
+{
+	int index = 0;
+
+	if (id) {
+		index = of_property_match_string(node,
+						 "reset-names", id);
+		if (index < 0)
+			return ERR_PTR(-ENOENT);
+	}
+	return of_reset_control_get_by_index(node, index);
+}
 EXPORT_SYMBOL_GPL(of_reset_control_get);
 
 /**
@@ -215,16 +235,10 @@ EXPORT_SYMBOL_GPL(of_reset_control_get);
  */
 struct reset_control *reset_control_get(struct device *dev, const char *id)
 {
-	struct reset_control *rstc;
-
 	if (!dev)
 		return ERR_PTR(-EINVAL);
 
-	rstc = of_reset_control_get(dev->of_node, id);
-	if (!IS_ERR(rstc))
-		rstc->dev = dev;
-
-	return rstc;
+	return of_reset_control_get(dev->of_node, id);
 }
 EXPORT_SYMBOL_GPL(reset_control_get);
 

drivers/reset/hisilicon/Kconfig

@@ -0,0 +1,5 @@
+config COMMON_RESET_HI6220
+	tristate "Hi6220 Reset Driver"
+	depends on (ARCH_HISI && RESET_CONTROLLER)
+	help
+	  Build the Hisilicon Hi6220 reset driver.

drivers/reset/hisilicon/Makefile

@@ -0,0 +1 @@
+obj-$(CONFIG_COMMON_RESET_HI6220) += hi6220_reset.o

drivers/reset/hisilicon/hi6220_reset.c

@@ -0,0 +1,109 @@
+/*
+ * Hisilicon Hi6220 reset controller driver
+ *
+ * Copyright (c) 2015 Hisilicon Limited.
+ *
+ * Author: Feng Chen <puck.chen@hisilicon.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/bitops.h>
+#include <linux/of.h>
+#include <linux/reset-controller.h>
+#include <linux/reset.h>
+#include <linux/platform_device.h>
+
+#define ASSERT_OFFSET            0x300
+#define DEASSERT_OFFSET          0x304
+#define MAX_INDEX                0x509
+
+#define to_reset_data(x) container_of(x, struct hi6220_reset_data, rc_dev)
+
+struct hi6220_reset_data {
+	void __iomem			*assert_base;
+	void __iomem			*deassert_base;
+	struct reset_controller_dev	rc_dev;
+};
+
+static int hi6220_reset_assert(struct reset_controller_dev *rc_dev,
+			       unsigned long idx)
+{
+	struct hi6220_reset_data *data = to_reset_data(rc_dev);
+
+	int bank = idx >> 8;
+	int offset = idx & 0xff;
+
+	writel(BIT(offset), data->assert_base + (bank * 0x10));
+
+	return 0;
+}
+
+static int hi6220_reset_deassert(struct reset_controller_dev *rc_dev,
+				 unsigned long idx)
+{
+	struct hi6220_reset_data *data = to_reset_data(rc_dev);
+
+	int bank = idx >> 8;
+	int offset = idx & 0xff;
+
+	writel(BIT(offset), data->deassert_base + (bank * 0x10));
+
+	return 0;
+}
+
+static struct reset_control_ops hi6220_reset_ops = {
+	.assert = hi6220_reset_assert,
+	.deassert = hi6220_reset_deassert,
+};
+
+static int hi6220_reset_probe(struct platform_device *pdev)
+{
+	struct hi6220_reset_data *data;
+	struct resource *res;
+	void __iomem *src_base;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	src_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(src_base))
+		return PTR_ERR(src_base);
+
+	data->assert_base = src_base + ASSERT_OFFSET;
+	data->deassert_base = src_base + DEASSERT_OFFSET;
+	data->rc_dev.nr_resets = MAX_INDEX;
+	data->rc_dev.ops = &hi6220_reset_ops;
+	data->rc_dev.of_node = pdev->dev.of_node;
+
+	reset_controller_register(&data->rc_dev);
+
+	return 0;
+}
+
+static const struct of_device_id hi6220_reset_match[] = {
+	{ .compatible = "hisilicon,hi6220-sysctrl" },
+	{ },
+};
+
+static struct platform_driver hi6220_reset_driver = {
+	.probe = hi6220_reset_probe,
+	.driver = {
+		.name = "reset-hi6220",
+		.of_match_table = hi6220_reset_match,
+	},
+};
+
+static int __init hi6220_reset_init(void)
+{
+	return platform_driver_register(&hi6220_reset_driver);
+}
+
+postcore_initcall(hi6220_reset_init);

drivers/reset/reset-ath79.c

@@ -15,13 +15,17 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/reset-controller.h>
+#include <linux/reboot.h>
 
 struct ath79_reset {
 	struct reset_controller_dev rcdev;
+	struct notifier_block restart_nb;
 	void __iomem *base;
 	spinlock_t lock;
 };
 
+#define FULL_CHIP_RESET 24
+
 static int ath79_reset_update(struct reset_controller_dev *rcdev,
 			unsigned long id, bool assert)
 {
@@ -72,10 +76,22 @@ static struct reset_control_ops ath79_reset_ops = {
 	.status = ath79_reset_status,
 };
 
+static int ath79_reset_restart_handler(struct notifier_block *nb,
+				unsigned long action, void *data)
+{
+	struct ath79_reset *ath79_reset =
+		container_of(nb, struct ath79_reset, restart_nb);
+
+	ath79_reset_assert(&ath79_reset->rcdev, FULL_CHIP_RESET);
+
+	return NOTIFY_DONE;
+}
+
 static int ath79_reset_probe(struct platform_device *pdev)
 {
 	struct ath79_reset *ath79_reset;
 	struct resource *res;
+	int err;
 
 	ath79_reset = devm_kzalloc(&pdev->dev,
 				sizeof(*ath79_reset), GFP_KERNEL);
@@ -96,13 +112,25 @@ static int ath79_reset_probe(struct platform_device *pdev)
 	ath79_reset->rcdev.of_reset_n_cells = 1;
 	ath79_reset->rcdev.nr_resets = 32;
 
-	return reset_controller_register(&ath79_reset->rcdev);
+	err = reset_controller_register(&ath79_reset->rcdev);
+	if (err)
+		return err;
+
+	ath79_reset->restart_nb.notifier_call = ath79_reset_restart_handler;
+	ath79_reset->restart_nb.priority = 128;
+
+	err = register_restart_handler(&ath79_reset->restart_nb);
+	if (err)
+		dev_warn(&pdev->dev, "Failed to register restart handler\n");
+
+	return 0;
 }
 
 static int ath79_reset_remove(struct platform_device *pdev)
 {
 	struct ath79_reset *ath79_reset = platform_get_drvdata(pdev);
 
+	unregister_restart_handler(&ath79_reset->restart_nb);
 	reset_controller_unregister(&ath79_reset->rcdev);
 
 	return 0;

drivers/reset/reset-berlin.c

@@ -87,9 +87,7 @@ static int berlin2_reset_probe(struct platform_device *pdev)
 	priv->rcdev.of_reset_n_cells = 2;
 	priv->rcdev.of_xlate = berlin_reset_xlate;
 
-	reset_controller_register(&priv->rcdev);
-
-	return 0;
+	return reset_controller_register(&priv->rcdev);
 }
 
 static const struct of_device_id berlin_reset_dt_match[] = {

drivers/reset/reset-socfpga.c

@@ -133,9 +133,8 @@ static int socfpga_reset_probe(struct platform_device *pdev)
 	data->rcdev.nr_resets = NR_BANKS * BITS_PER_LONG;
 	data->rcdev.ops = &socfpga_reset_ops;
 	data->rcdev.of_node = pdev->dev.of_node;
-	reset_controller_register(&data->rcdev);
 
-	return 0;
+	return reset_controller_register(&data->rcdev);
 }
 
 static int socfpga_reset_remove(struct platform_device *pdev)

drivers/reset/reset-sunxi.c

@@ -108,9 +108,8 @@ static int sunxi_reset_init(struct device_node *np)
 	data->rcdev.nr_resets = size * 32;
 	data->rcdev.ops = &sunxi_reset_ops;
 	data->rcdev.of_node = np;
-	reset_controller_register(&data->rcdev);
 
-	return 0;
+	return reset_controller_register(&data->rcdev);
 
 err_alloc:
 	kfree(data);
@@ -122,7 +121,7 @@ err_alloc:
  * our system, before we can even think of using a regular device
  * driver for it.
  */
-static const struct of_device_id sunxi_early_reset_dt_ids[] __initdata = {
+static const struct of_device_id sunxi_early_reset_dt_ids[] __initconst = {
 	{ .compatible = "allwinner,sun6i-a31-ahb1-reset", },
 	{ /* sentinel */ },
 };