This enables the sun linux logo to be selected on sparc32.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bob Breuerauthored and David S. Millercommited 2005-04-24 20:42:45 -07:00
Using the same logic as the other framebuffer fixes committed in 2.6.11,
this is a set of fixes to make TCX functional on the console again. Adds
the tcx_pan_display function, sets the
all->info.var.{red,green,blue}.length values to 8, and runs fb_set_cmap.
Also looks for the correct SUNW,tcx prom value.
This patch just slipped through the cracks.
Originally by: Georg Chini <georg.chini@triaton-webhosting.com>
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom 'spot' Callawayauthored and David S. Millercommited 2005-04-24 20:39:15 -07:00
Minor cleanups for sparc specific drivers (sunbmac, sunqe, sunlance,
sunhme, esp) so that they have a full module version definition that is
consistent with other upstream drivers.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom 'spot' Callawayauthored and David S. Millercommited 2005-04-24 20:35:20 -07:00
From: Panagiotis Issaris <takis@lumumba.luc.ac.be>
In the ENI155P device driver in six possible failure cases the requested
irq is not being released.
In three of the above possible failure cases additionally there seems to
be a memory leak.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Mortonauthored and David S. Millercommited 2005-04-24 19:14:36 -07:00
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
chas williamsauthored and David S. Millercommited 2005-04-24 18:55:35 -07:00
Replacing the open coded equivalents and making ax25 look more like
a linux network protocol, i.e. more similar to inet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnaldo Carvalho de Meloauthored and David S. Millercommited 2005-04-24 18:53:06 -07:00
void * __iomem foo is not a pointer to iomem - it's an iomem variable
containing void *. A pile of such guys in arch/sparc64/kernel/time.c,
drivers/sbus/char/rtc.c and include/asm-sparc64/mostek.h turned into
intended void __iomem *.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viroauthored and Linus Torvaldscommited 2005-04-24 12:28:36 -07:00
(!ARCH_S390 && !M68K && !IA64 && !UML) is obviously always true on ARM.
Intended behaviour for ARM is "absent unless we are on RiscPC or
EBSA285". So what we want is added && !ARM in the first term - without
it the last part (|| ARCH_RPC || ARCH_EBSA285, that is) doesn't do
anything.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viroauthored and Linus Torvaldscommited 2005-04-24 12:28:35 -07:00
Missing include, breaks at least on arm.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viroauthored and Linus Torvaldscommited 2005-04-24 12:28:35 -07:00
All boards dealt with by I2C_MPC are 32bit. Moreover, driver simply
won't build on ppc64 - it uses ppc32-only types all over the place.
Dependency fixed - it's PPC32, not PPC.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viroauthored and Linus Torvaldscommited 2005-04-24 12:28:35 -07:00
Somebody forgot that | has higher priority than ?:. As the result,
allocation is done with bogus flags - instead of GFP_ATOMIC + possibly
GFP_DMA we always get GFP_DMA and no GFP_ATOMIC.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viroauthored and Linus Torvaldscommited 2005-04-24 12:28:34 -07:00
We were forgetting to call sunsu_change_speed(). The reason
that replugging in the mouse cable "fixes things" is that
causes a BREAK interrupt which in turn caused a call to
sunsu_change_speed() which would get the chip setup properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Millercommited 2005-04-21 22:06:13 -07:00
Provide support for drivers/char/rtc.c ioctls in the
Mostek rtc driver as well as the Sparc specific RTCGET
and RTCSET.
This allows userspace to be much less messy. Currently
util-linux and other spots jump through hoops trying
various ioctl variants until it hits the right one whatever
driver actually being used supports.
Eventually all of this should move over to the genrtc.c
driver, but not today...
While we are here, fix up the register types for sparse.
Thanks to Frans Pop for helping point out this issue.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Millercommited 2005-04-21 21:42:34 -07:00
Add MSI test for chips that support MSI. If MSI test fails, it will
switch back to INTx mode and will print a message asking the user to
report the failure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:13:59 -07:00
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the
offset is not 4-byte aligned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:12:46 -07:00
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out
is enabled, certain NVRAM registers cannot be written to.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:12:05 -07:00
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as
output when it is unused.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:10:36 -07:00
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:09:53 -07:00
Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:09:08 -07:00
Setup proper GPIO settings in tp->grc_local_ctrl before calling
tg3_set_power() state in tg3_get_invariants() and after chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:07:04 -07:00
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.
On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:06:20 -07:00
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chanauthored and David S. Millercommited 2005-04-21 17:05:28 -07:00
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:03:52 -07:00
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:03:18 -07:00
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and
TG3_FLG2_5750_PLUS flags.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:02:41 -07:00
Rewrite of a couple of troublesome multi-way if statements to use
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:02:04 -07:00
Replace a number of two-way if statements checking for 5750, and/or
5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:01:29 -07:00
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:00:52 -07:00
Replace a number of three-way if statements checking for 5705, 5750,
and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 17:00:02 -07:00
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 16:58:56 -07:00
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl.
Next patch will change entry to use pci_ids.h-based definition.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 16:57:50 -07:00
Add ASIC_REV_5752 definition.
Track-down all references to ASIC_REV_5750 and mirror them with
references to the newly defined ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linvilleauthored and David S. Millercommited 2005-04-21 16:56:08 -07:00
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's
allocation fix. Multichannel ISO receive still sucks; it should be possible
to use both legacy and non-legacy modes at the same time, but with this
patch, things are no worse than they were in 2.6.11 and allocation is
still done at the correct time.
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jody McIntyreauthored and Linus Torvaldscommited 2005-04-21 14:09:42 -07:00
- Print the correct value in the DBGMSG in dma_rcv_tasklet().
See OHCI 1.1 section 8.7, page 103 ff.
- Print tlabels as %d everywhere.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jody McIntyreauthored and Linus Torvaldscommited 2005-04-21 14:09:42 -07:00
We do not longer use DLT_LINUX_SLL for activ/pass filters but
DLT_PPP_WITHDIRECTION witch need 1 as outbound flag.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Karsten Keilauthored and Linus Torvaldscommited 2005-04-21 08:30:30 -07:00
My version of gcc doesn't warn about this error (declaration in the
middle of a set of statements).
The fix is simple (this also corrects return code; for init functions it
should be zero or error).
James Bottomleyauthored and Linus Torvaldscommited 2005-04-21 07:35:45 -07:00
Linus Torvalds
commited 
Bob Breuer
authored and
David S. Miller
commited 
Tom 'spot' Callaway
authored and
Andrew Morton
authored and
Jesper Juhl
authored and
chas williams
authored and
Arnaldo Carvalho de Melo
authored and
Al Viro
authored and
Al Viro
authored and
David S. Miller
commited 
Michael Chan
authored and
John W. Linville
authored and
Adrian Bunk
authored and
Jody McIntyre
authored and
Karsten Keil
authored and
James Bottomley
authored and
Linus Torvalds
commited