This is driver for EasyPoint AS5011 2 axis joystick chip. This chip is
plugged on an I2C bus.
Tested on ARM processor (i.MX27).
Signed-off-by: Fabien Marteau <fabien.marteau@armadeus.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fabien Marteauauthored and Dmitry Torokhovcommited 2011-01-10 11:01:43 -08:00
Add force-feedback support for N64 pads with rumble pak accessory installed.
Actually we do not check for the presence of rumble pad but simply assume it
is installed and expect the device to ignore FF commands if rumble pak is
missing.
Signed-off-by: Scott Moreau <oreaus@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Scott Moreauauthored and Dmitry Torokhovcommited 2010-02-21 22:09:43 -08:00
Add support for the SEGA Dreamcast Maple controller as a joystick
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adrian McMenaminauthored and Dmitry Torokhovcommited 2008-12-30 00:58:05 -08:00
This is a driver for Zhen Hua PPM-4CH RC transmitter (commonly used in cheap
Ready To Fly RC helicopters by Walkera) which using "Zhen Hua 5-byte protocol"
for using them as a four axis joystick via serial port. Transmitter connected
to serial port (19200 8N1) sending periodically 5 bytes where first byte is for
synchronization and next four bytes are values of axis.
Signed-off-by: Martin Kebert <gkmarty@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Martin Kebertauthored and Dmitry Torokhovcommited 2008-04-15 13:26:52 -04:00
Input: xpad - fix dependancy on LEDS class
The driver can not be built-in when LEDS class is a module.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmitry Torokhovauthored and Linus Torvaldscommited 2007-09-28 15:38:12 -07:00
Export LEDs on Xbox360 pad via led subsystem as a single device in
/sys/class/leds/xpad[0-9]+.
Xbox360 pad has four leds, which form a circle. Unfortunately the leds
can't be controlled independently and can only display a predefined
set of patterns (for example one is turned on wile others are off or
a rotating pattern - 1-2-3-4). To activate a pattern one needs to send
a specific command to the device (see http://www.free60.org/wiki/Gamepad).
Led subsystem allows us to set brightness, but there is nothing like
brightness on this device. So brightness is actually interpreted as
the command (only values between 0 and 14 are accepted).
Signed-off-by: Jan Kratochvil <honza@jikos.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Jan Kratochvilauthored and Dmitry Torokhovcommited 2007-07-18 00:35:40 -04:00
Implementation is using force feedback support for memoryless devices.
Signed-off-by: Jan Kratochvil <honza@jikos.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Jan Kratochvilauthored and Dmitry Torokhovcommited 2007-07-10 00:35:15 -04:00
stuff that does select USB should depend on USB_ARCH_HAS_HCD, or we'll
end up with unbuildable configs.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viroauthored and Linus Torvaldscommited 2007-05-15 18:56:37 -07:00
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Fabien Marteau
authored and
Dmitry Torokhov
commited 
Scott Moreau
authored and
Adrian McMenamin
authored and
Peter Popovec
authored and
Martin Kebert
authored and
Linus Torvalds
commited 
Jan Kratochvil
authored and
Dmitry Torokhov
commited 
Al Viro
authored and
Matt LaPlante
authored and
Adrian Bunk
commited 
Linus Torvalds
commited