megaraid_sas suspend and resume are inappropriatelly placed in
__devinit section. Remove those placements and make the stuff
dependent on CONFIG_PM.
While at it, mark remove function as __devexit.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jiri Slabyauthored and James Bottomleycommited 2008-05-02 13:07:56 -05:00
Update the Version and Changelog for megaraid_sas Driver
Signed-off-by: Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-04-29 19:43:12 -05:00
Newer Dell CERC firmware (>= 6.62) implement a random deletion handling
compatible with the legacy megaraid driver. The legacy handling shifted
the target ID by 0x80 only for I/O commands (READ/WRITE/etc), whereas
megaraid_mbox shifts the target ID always if random deletion is supported.
The resulted in megaraid_mbox sending an INQUIRY to the wrong channel, and
not finding any devices, obviously.
So we disable the random deletion support if the offending firmware is
found.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=6695
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hannes Reineckeauthored and James Bottomleycommited 2008-04-29 19:34:07 -05:00
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Jonesauthored and Greg Kroah-Hartmancommited 2008-04-19 19:10:33 -07:00
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Add the new Controller (ID: 007C) support to driver.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-04-07 12:19:00 -05:00
When Driver sent wrong frame count to firmware. As this particular
command is sent to drive, FW is seeing continuous chip resets and so
the command will timeout.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-04-07 12:19:00 -05:00
Sense buffer ptr data type in the ioctl path is reverted back to u32 *
as in previous versions of driver.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-04-07 12:19:00 -05:00
The MegaRAID driver's common management module (megaraid_mm.c) creates a
char device used by the management tool "megarc" from LSI Logic (and
possibly other management tools).
In 2.6 with udev, this device doesn't get created because it is not
registered in sysfs.
I first fixed this by registering a class "megaraid_mm", but realized that
this should probably be moved to misc devices, instead of taking up a char
major. This is because only 1 device is used, even if there are multiple
adapters - the minor is never used (the adapter info is in the ioctl block
sent to the driver, not detected based on the minor number as one might
think). So it is a complete waste to have an entire major taken by this.
So it now uses a misc device which I named "megadev0" (the name that megarc
expects), and has a dynamic minor (previoulsy a dynamic major was used).
I have tested this on my own system with the megarc tool, and it works just
as fine as before (only now the device gets created correctly by udev).
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Thomas Horstenauthored and James Bottomleycommited 2008-02-11 10:20:53 -06:00
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Joe Perchesauthored and Adrian Bunkcommited 2008-02-03 17:28:22 +02:00
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomleycommited 2008-01-30 13:14:02 -06:00
Change megaraid_pci_driver_g variable name so that it matches the modpost
whitelist that allows pointers to init text/data.
WARNING: vmlinux.o(.data+0x1a8e30): Section mismatch: reference to .init.text:megaraid_probe_one (between 'megaraid_pci_driver_g' and 'class_device_attr_megaraid_mbox_app_hndl')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Randy Dunlapauthored and James Bottomleycommited 2008-01-23 11:29:26 -06:00
Added module parameter "poll_mode_io" to support for "polling"
(reduced interrupt operation). In this mode, IO completion interrupts
are delayed. At the end of initiating IOs, the driver schedules for
cmd completion if there are pending cmds. A timer-based interrupt has
also been added to prevent IO completion from being delayed
indefinitely in the case that no new IOs are initiated. Some
formatting issues in resume, suspend comment block also corrected
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-01-11 18:22:44 -06:00
Driver will call cmd completion routine from Reset path without waiting for cmd completion from isr context.
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-01-11 18:22:43 -06:00
MegaRAID utilities expect sense_buff to be of type unsigned long.
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-01-11 18:22:43 -06:00
1. Setting the max_sectors_per_req based on max SGL supported by the
FW. Prior versions calculated this value from controller info's
max_sectors_1, max_sectors_2. For certain controllers/FW, this was
resulting in a value greater than max SGL supported by the FW. Now
we take the min of max sgl from FW and max_sectors calculation.
2. Increased MFI_POLL_TIMEOUT_SECS to 60 seconds from 10. FW may take
a max of 60 seconds to respond to the INIT cmd.
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-01-11 18:22:43 -06:00
Adding hibernation support. suspend, resume routine implemented.
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yangauthored and James Bottomleycommited 2008-01-11 18:22:43 -06:00
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Bo Yang <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Matthias Kaehlckeauthored and James Bottomleycommited 2008-01-11 18:22:41 -06:00
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Robert P. J. Dayauthored and Adrian Bunkcommited 2007-10-19 23:10:43 +02:00
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
FUJITA Tomonoriauthored and Jens Axboecommited 2007-10-16 11:24:32 +02:00
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yoann Padioleauauthored and Linus Torvaldscommited 2007-07-19 10:04:50 -07:00
The Megaraid Mailbox driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthias Kaehlckeauthored and James Bottomleycommited 2007-07-14 19:10:19 -05:00
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
FUJITA Tomonoriauthored and James Bottomleycommited 2007-05-31 18:38:36 -04:00
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
FUJITA Tomonoriauthored and James Bottomleycommited 2007-05-31 18:11:55 -04:00
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: intercept cmd timeout and throttle io
[SCSI] fusion: Fix |/|| confusion
[SCSI] aic94xx: asd_clear_nexus should fail if the cleared task does not complete
[SCSI] aic7xxx: fix aicasm build failure with gcc-3.4.6
[SCSI] aacraid: apply commit config for reset_devices flag
[SCSI] sd: fix refcounting regression in suspend/resume routines
[SCSI] aacraid: fix panic on short Inquiry
[SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
[SCSI] NCR53C9x: correct spelling mistake in deprecation notice
[SCSI] tgt: fix a rdma indirect transfer error bug
[SCSI] MegaRAID: Update MAINTAINERS email-id
[SCSI] stex: minor cleanup and version update
[SCSI] stex: fix reset recovery for console device
[SCSI] stex: extend hard reset wait time
[SCSI] stex: fix id mapping issue
[SCSI] ipr: Proper return codes for eh_dev_reset for SATA devices
[SCSI] zfcp: IO stall after deleting and path checker changes after reenabling zfcp devices
[SCSI] zfcp: avoid clutter in erp_dbf
eh_timed_out call back (megasas_reset_timer) is used to throttle io
to the adapter when it is called the first time for a scmd.
The MEGASAS_FW_BUSY flag is set and can_queue reduced to 16.
The can_queue is restored from completion routine in following
two conditions : 5 seconds has elapsed and
the # of outstanding cmds in FW is < 17.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2007-05-24 09:08:27 -05:00
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyanauthored and Linus Torvaldscommited 2007-05-21 09:18:19 -07:00
Update the driver version reported by MEGAIOC_QDRVRVER to
match LSI_COMMON_MOD_VERSION.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
David Milburnauthored and James Bottomleycommited 2007-05-06 09:33:11 -05:00
FW does not support SYNCHRONIZE_CACHE cmd. FW flush cache on its own.
So, we just return success from the megasas_queue_command.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2007-02-16 10:43:41 -06:00
Replaced pci_alloc_consistent with dma_alloc_coherent from the ioctl path.
This is to avoid situations where ioctl fails for lack of memory
(when system under heavy stress).
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2007-02-16 10:20:33 -06:00
Checks if hw_crit_error is set.
If it is set, we donot process commands.
Checks added in megasas_queue_command and command completion routines.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2007-02-16 10:15:29 -06:00
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Venauthored and Linus Torvaldscommited 2007-02-12 09:48:45 -08:00
More megaraid kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sumant Patro <sumantp@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Randy Dunlapauthored and James Bottomleycommited 2007-01-13 13:55:35 -06:00
kernel-doc modifications:
- change "@param var" notation to @var;
- change function/description separator from ':' to '-';
- change var/description separator from '-' to ':';
- fix a few doc. typos;
- don't use kernel-doc /** lead-in when the doc. block is not kernel-doc;
- use Linux common */ ending comment format instead of **/;
- use correct function parameter names;
- place function parameters immediately after the function short description;
- place kernel-doc immediately before its function or macro;
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sumant Patro <sumantp@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Randy Dunlapauthored and James Bottomleycommited 2007-01-13 13:55:01 -06:00
1. Changes in Initialization to fix kdump failure.
Send SYNC command on loading.
This command clears the pending commands in the adapter
and re-initialize its internal RAID structure.
Without this change, megaraid driver either panics or fails to
initialize the adapter during kdump's second kernel boot
if there are pending commands or interrupts from other devices
sharing the same IRQ.
2. Authors email-id domain name changed from lsil.com to lsi.com.
Also modified the MODULE_AUTHOR to megaraidlinux@lsi.com
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2007-01-13 13:54:23 -06:00
Update domain name change from lsil.com to lsi.com.
Change module author to megaraidlinux@lsi.com
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2007-01-06 09:21:47 -06:00
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adrian Bunkauthored and James Bottomleycommited 2006-11-22 12:15:47 -06:00
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Acked-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrey Mirkinauthored and Linus Torvaldscommited 2006-10-16 08:30:04 -07:00
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
- handle clear_user() error
- handle and properly unwind from sysfs errors thrown during mod init
- adjust order of calls in megasas_exit() to precisely match
registration order in megasas_init()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updated for extra attribute and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jeff Garzikauthored and James Bottomleycommited 2006-10-04 13:26:25 -05:00
This patch sets timeout of max 180 seconds for ioctl completion.
It also updates the Changelog and hikes the version to 3.05.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2006-10-04 12:55:29 -05:00
This patch adds a tasklet for command completion.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patroauthored and James Bottomleycommited 2006-10-04 12:53:42 -05:00
Jiri Slaby
authored and
James Bottomley
commited 
bo yang
authored and
Hannes Reinecke
authored and
Linus Torvalds
commited 
Tony Jones
authored and
Greg Kroah-Hartman
commited 
Matthew Wilcox
commited 
Thomas Horsten
authored and
Daniel Walker
authored and
Linus Torvalds
commited 
Joe Perches
authored and
Adrian Bunk
commited 
Randy Dunlap
authored and
Matthias Kaehlcke
authored and
Jens Axboe
commited 
Robert P. J. Day
authored and
FUJITA Tomonori
authored and
Yoann Padioleau
authored and
James Bottomley
commited 
FUJITA Tomonori
authored and
James Bottomley
commited 
Sumant Patro
authored and
Alexey Dobriyan
authored and
David Milburn
authored and
Sumant Patro
authored and
Arjan van de Ven
authored and
Adrian Bunk
authored and
Andrey Mirkin
authored and
Linus Torvalds
commited 
David Howells
commited 
Jeff Garzik
authored and